Table of Contents
Advertisement
1
From the VIRB® screen, select
2
Wait a few seconds for the thumbnail images to load.
3
Select a video or image.
4
Select Menu > Start Slideshow.
To stop the slideshow, selcet Menu > Stop Slideshow.
VIRB Action Camera Settings
NOTE: Not all options and settings apply to all camera models.
Select OneHelm™, A/V, Gauges > VIRB® > Menu.
Name: Allows you to enter a new name for the VIRB action
camera.
Recording: Starts and stops recording.
Take Photo: Takes a still photograph.
Playback: Allows you to view video recordings and photos.
Freeze: Pauses the camera image.
Sleep: Puts the VIRB action camera into a low power mode to
conserve battery power. Not available on the VIRB 360
camera.
Video Setup: Sets up the video
Setup Settings, page
53).
Edit Overlays: Adjusts the data shown on the screen
(Customizing the Data Overlays, page
VIRB Action Camera Video Setup Settings
NOTE: Not all options and settings apply to all camera models.
Select OneHelm™, A/V, Gauges > VIRB® > Menu > Video
Setup.
Aspect: Sets the video aspect ratio.
Video Mode: Sets the video mode. For example, you can select
the Slow-Mo option to shoot slow motion videos.
Video Size: Sets the size or pixel dimensions of videos.
Video FPS: Sets the frames per second.
Video Timestamp: Adds the date and time a video was
recorded.
Photo Timestamp: Adds the date and time a photo was taken.
Photo Size: Sets the size or pixel dimensions of photos.
Field of View: Sets the zoom level.
Lens Mode: Sets which lens or lenses the camera uses while
shooting video.
Mirror: Allows you to flip or mirror the video.
Rotation: Allows you to rotate the camera angle.
Adding the VIRB Action Camera Controls to Other
Screens
Before you can control a VIRB action camera with the
chartplotter, you must connect the devices using a wireless
connection
(Connecting a Wireless Device to the Chartplotter,
page
6).
You can add the VIRB action camera control bar to other
screens. This allows you to start and stop recording from other
functions in the chartplotter.
1
Open the screen to which you want to add the VIRB action
camera control bar.
2
Select Menu > Edit Overlays > Bottom Bar > VIRB Bar.
When viewing a screen that has the VIRB action camera
controls, you can select
VIRB action camera.
Device Configuration
.
(VIRB Action Camera Video
4).
to open the full screen view of the
HDMI
Out Video Considerations
®
To prevent corrosion due to moisture, you must use Garmin
GPSMAP
®
accessory cables when connecting the chartplotter to
the video display. Using different cables voids your warranty.
Through the HDMI OUT port, you can duplicate the chartplotter
screen on another device, such as a television or monitor.
The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft.)
long. If you need a longer cable, you should use an active HDMI
cable only. You need an HDMI coupler to connect the two HDMI
cables.
You must make all cable connections in a dry environment.
Item Description
GLASS COCKPIT chartplotter
GPSMAP HDMI cable (HDMI OUT)
Display with an HDMI In port, such as a computer or television
Dry environment, protected from moisture
Pairing the GC
100 Camera with a Garmin
™
Chartplotter
Before you can connect a wireless device to the chartplotter
wireless network, you must configure the chartplotter wireless
network.
1
With the camera within an unobstructed 76 m (250 ft.) of the
chartplotter, quickly press
2
On the chartplotter, select Settings > Communications >
Wireless Devices > Garmin Camera > Start.
3
Follow the on-screen instructions.
Device Configuration
System Settings
Select Settings > System.
Sounds and Display: Adjusts the display and audio settings.
GPS: Provides information about the GPS satellites and
settings.
System Information: Provides information about the devices on
the network and the software version.
Station Information: Adjusts the setup of the station.
Auto Power Off: Automatically turns off the system after it has
been asleep for the selected length of time.
Simulator: Turns the simulator on or off and allows you to set
the time, date, speed, and simulated location.
Sounds and Display Settings
Select Settings > System > Sounds and Display.
Beeper: Turns on and off the tone that sounds for alarms and
selections.
Backlight: Sets the backlight brightness. You can select the
Auto option to adjust the backlight brightness automatically
based on the ambient light.
Backlight Sync: Synchronizes the backlight brightness of other
chartplotters in the station.
NOTICE
three times.
53
Advertisement
Table of Contents
