Table of Contents
Advertisement
Setting the Graph Range and Time Scales
You can indicate the amount of time and the range of depth that
appear in the depth and water temperature graphs.
1
From a graph, select Graph Setup.
2
Select an option:
• To set a time-elapsed scale, select Duration. The default
setting is 10 minutes. Increasing the time-elapsed scale
allows you to view variations over a longer period of time.
Decreasing the time-elapsed scale allows you to view
more detail over a shorter period of time.
• To set the graph scale, select Scale. Increasing the scale
allows you to view more variation in readings. Decreasing
the scale allows you to view more detail in the variation.
Vessel Information
When the chartplotter is connected to a compatible EVC 2.0
Volvo Penta engine, you can view information about the engine.
Select Info > Vessel Info.
Maintenance Assistant
When the chartplotter is connected to a compatible Volvo Penta
engine, you can view the time to the next engine service, in
engine hours remaining and days remaining.
Select Info > Vessel Info > Maintenance Assistant.
After you have serviced the engine, select the engine, and
select Reset Service Reminder.
Oil Level Information
When the chartplotter is connected to a compatible Volvo Penta
engine and an engine oil level sensor or a transmission oil level
sensor, you can view information about the engine oil level and
transmission oil level.
Select Info > Vessel Info > Oil Level.
Driveline Information
When the chartplotter is connected to a compatible Volvo Penta
engine, you can view information about the engine type,
driveline count, drive type, engine rate, electrical system, and
EVC generation.
Select Info > Vessel Info > Driveline Info.
EVC Network Information
When the chartplotter is connected to a compatible Volvo Penta
engine, you can view information about the EVC network, such
as features, components, software versions, and calibration.
Select Info > Vessel Info > EVC Network.
inReach
Do not read or reply to notifications while operating the vessel.
Failure to pay attention to the conditions on the water can result
in vessel damage, personal injury, or death.
You can connect an inReach Mini device to the chartplotter to
view, reply to, and send preset messages from the chartplotter.
NOTE: The inReach Mini device must be connected to the
chartplotter and receiving satellite signals to send and receive
messages using the chartplotter.
To open the InReach® page, select OneHelm™, A/V, Gauges
> InReach®.
44
Messages
®
WARNING
Connecting an inReach Device to the
Chartplotter
You can connect a compatible inReach device to the chartplotter
to manage messages.
1
Bring the inReach device within 3 m (10 ft.) of the
chartplotter.
2
From the main menu of the inReach device, select Setup >
ANT+ > Status > On.
3
On the chartplotter, select OneHelm™, A/V, Gauges >
InReach® > Start Pairing.
The chartplotter begins searching for and connecting to the
inReach device. This can take up to 60 seconds.
4
If necessary, compare the code on the inReach device to the
chartplotter, and select OK if they match.
The inReach and chartplotter connect automatically when they
are within range.
Receiving inReach Messages
When your inReach device receives a message, a pop-up
notification appears briefly on the GLASS COCKPIT screen.
• To review the full message, select Review.
• To dismiss the pop-up notification, select OK or wait for the
notification to close automatically.
Sending an inReach Preset Message
Preset messages are messages that you created at
explore.garmin.com. Preset messages have predefined text and
recipients.
1
From the InReach® page, select Messages > Send
inReach Preset.
2
Select a preset message.
3
Select Send.
Replying to an inReach Message
You can reply to an inReach message with a pre-written
message.
1
From the InReach® page, select Messages.
A list of sent and received messages appears.
2
Select a received message.
3
Select Reply.
4
Select a message.
5
Select Send.
Digital Switching
Your chartplotter can be used to monitor and control circuits
when a compatible system is connected.
For example, you can control the interior lights and navigation
lights on the vessel. You can also monitor live well circuits.
To access the digital switching controls, select OneHelm™, A/V,
Gauges > Switching.
For more information about purchasing and configuring a digital
switching system, contact your Garmin dealer.
Adding and Editing a Digital Switching Page
You can add and customize digital switching pages to the
chartplotter.
1
Select OneHelm™, A/V, Gauges > Switching > Menu >
Setup.
2
Select Add Page or Edit Page.
3
Set up the page as needed:
• To enter a name for the page, select Name.
Vessel Information
Advertisement
Table of Contents
