Seven Marine Engine Installation Settings; Other Vessels Settings; Settings That Are Synced On The Garmin Marine Network; Restoring The Original Chartplotter Factory Settings - Volvo Penta Glass cockpit Owner's Manual

Seven Marine Engine Installation Settings

Select Settings > My Vessel > Seven Marine Installation.
DPS Button: Allows you to set the joystick button DPS modes.
Trim Zero Set: Allows you to initialize the trim angle to zero
when all motors are fully trimmed down.
Tank Preset: Sets the tank name, fluid type, sensor style, and
tank capacity, and calibrates the sensor
Tank Level Sensors, page
Air Purge: Allows you to bleed air from the steering system
using the steering pumps.
Steer Sensor: Calibrates the engine steering system using
physical end stops. A physical end stop is the point at which
a steering wheel stops turning in a direction.
Joystick Thrust: Allows you to set how hard the thrusters work.
Larger boats may need to select Maximum for the boat to
move, while Maximum joystick thrust may provide too much
thrust for smaller boats.
Lock to Lock: Allows you to set the number of turns from lock to
lock.
Steer Friction: Sets the friction on the steering wheel. The
friction is adjusted automatically according to the engine
speed.
Engine Distance: Allows you to set the distance between drive
lines to limit achievable steering angles for certain engine
distances.
Gear Rotation: Allows you to set the type of gear case on the
outboard to define forward and reverse shift direction.
Gear Ratio: Allows you to set the ratio between the rotation
rates of the last and first gears.

Other Vessels Settings

When your compatible chartplotter is connected to an AIS
device or VHF radio, you can set up how other vessels are
displayed on the chartplotter.
Select Settings > Other Vessels.
AIS: Enables and disables AIS signal reception.
DSC: Enables and disables digital selective calling (DSC).
Collision Alarm: Sets the collision alarm
Collision Alarm, page 11).
AIS-EPIRB Test: Enables test signals from Emergency Position
Indicating Radio Beacons (EPRIB).
AIS-MOB Test: Enables test signals from man overboard (MOB)
devices.
AIS-SART Test: Enables test transmissions from Search and
Rescue Transponders (SART).
Settings that are Synced on the Garmin
Marine Network
The following devices sync certain settings when connected to
the Garmin Marine Network.
• ECHOMAP ™ 70 series
• GPSMAP 507 series (software version 3.0 or later)
• GPSMAP 701 series (software version 3.0 or later)
• GPSMAP 702 series
• GPSMAP 800 series
• GPSMAP 902 series
• GPSMAP 1000 series
• GPSMAP 1002 series
• GPSMAP 1202 series
• GPSMAP 7400/7600 series
• GPSMAP 8400/8600/8700 series
58
(Configuring the
43).
(Setting the Safe-Zone
The following settings are synced, if applicable, to the device.
Alarm Settings (also syncs alarm acknowledgment):
• Arrival
• Anchor Drag
• Off Course
• GPS Accuracy
• Shallow Water
• Deep Water (Not available in the GPSMAP 8400/8600
series)
• Water Temp.
• Contour (Not available in echoMAP 70s and GPSMAP
507/701 series)
• Fish
• Collision Alarm
General Settings:
• Auto Guidance Preferred Depth
• Auto Guidance Vertical Clearance
• Beeper
• Color Mode
• Keyboard Layout
• Language
• Map Datum
• North Reference
• Position Format
• System Units
• Calibrate Water Speed
• Radar Antenna Size
Chart Settings:
• Chart Borders
• Hazard Colors
• Heading Line
• Land POIs
• Light Sectors
• Navaid Size
• Navaid Type
• Photo Points
• Preferred Depth
• Shallow Shading
• Service Points
• Vessel Icon (Cannot be synced between all models)
Restoring the Original Chartplotter Factory
Settings
NOTE: This affects all devices on the network.
1
Select Settings > System > System Information > Reset.
2
Select an option:
• To reset the device settings to the factory default values,
select Reset Default Settings. This restores the default
configuration settings, but does not remove saved user
data, maps, or software updates.
• To reset all settings in all devices in the station to the
factory default values, select Reset Station Settings. This
restores the default configuration settings, but does not
remove saved user data, maps, or software updates
• To clear saved data, such as waypoints and routes, select
Delete User Data. This does not affect maps or software
updates.
Device Configuration