Advertisement
FACTORY DEFAULTS
Master Programming Code...........................................123456
Entry Code Length......................................................4 digits
Request-to-exit Output Relay......................................No Output
Alarm Shunt Output....................................................Disabled
Forced Entry Output................................................No Output
Door Ajar Output.....................................................No Output
Main Relay On Time...............................................02 Seconds
Auxiliary Relay On Time..........................................02 Seconds
Solid State Output #3 On Time.................................02 Seconds
Solid State Output #4 On Time.................................02 Seconds
Door Sense/Inhibit Input.........................................Door Sense
Keypad Lockout Output.............................................Disabled
Keypad Active Output................................................Disabled
Beeper Sounds When Key Pressed....................................Yes
Beeper Sounds During Relay #1..........................................No
Beeper Sounds During Relay #2..........................................No
Beeper Sounds During Output #3.........................................No
Beeper Sounds During Output #4.........................................No
Keypad Lockout Count.............................3 Tries Before Lockout
Anti-Passback Time.......................................No Anti-Passback
Auto-Relock....................................................................On
BASIC PROGRAMMING
When the 923 EntryCheck™ is in Programming Mode the yellow
indicator will blink slowly. After a programming command is
selected, the yellow indicator will flash rapidly while the keypad is
waiting for user input data. The green indicator will light if the data
is accepted. The red indicator will light if any programming data is
entered incorrectly, and the command will have to be fully re-
entered. IMPORTANT!: Codes are stored by User #. It is
imperative that the User numbers and their assigned personnel are
managed in the event a specific user ever needs to be deleted.
Entering Programming Mode
The 6-digit Master Programming Code (default = 123456) is used
to enter Programming Mode.
Press: # 9 # Master Code #
Master Code = the current 6-digit Master Programming Code
Exiting Programming Mode
Press:
The red indicator will light after exiting Programming Mode
Note: The 923 will automatically exit Programming Mode after 30
seconds of inactivity
Re-entering a Command After a Mistake
If the red indicator lights, signaling an incorrect entry, or an
incorrect key is pressed during programming, to clear the keypad
and re-enter the command:
Press:
Setting Entry Code Length
Press: 0 3 # Length #
Length = 4-6 for entry code length
Note: If the Entry Code Length is going to be changed from the factory
default of 4 digits, make this change first before programming any entry
codes.
P:\INSTALLATION INST\Access Controls\INST-923\INST-923.vsd
#
9 #
Default: 4 digits
Rev F
05-19
Page 4
Adding a New Entry Code
Press: 0 1 # User # Code # Code # Relay #
User = User number to be added (001-500). Must be unique.
Code=The new entry code: 1-999999, depending on code length
Relay=Relay output entry code will activate:
1=Main Relay 2=Auxiliary Relay 3=Both Relays
10=Relay #1, toggled 20=Relay #2, toggled 30=both Relays toggled
12=Relay #1 toggled; Relay #2 timed open
21=Relay #1 timed open; Relay #2 toggled
The yellow indicator will flash quickly while the 923 stores the new
user information in memory The green indicator will light when the
new user is accepted. If the user number already exists or an entry
error has been made, the red indicator will light. Delete the user and
re-enter the new information again.
Note: Leading zeros (zeros before the Code number, i.e.0001) do not need
to be entered when programming a new code. The 923 will internally add any
zeros to fill digits determined by the entry code length setting. Leading zeros
will have to be entered by the user when entering their code to gain access.
Changing a User PIN
Press: 04 # User # New Code # New Code #
User =The user number whose PIN will be changed
Erasing a Single Entry Code
Press: 0 2 # User # User #
User=The user ID to delete
The yellow indicator will flash quickly while the 923 searches its
memory for the User to erase. The green indicator will light when
the code is erased.
Erasing All Users
WARNING: PERFORMING THIS COMMAND WILL REMOVE
ALL USERS FROM THE MEMORY
Press: 9 7 # 0 0 0 0 0 0 # 0 0 0 0 0 0 #
Note: The green indicator will light while the memory is being erased. This
may take up to 15 seconds.
PROGRAMMING OPTIONS
There are several 923 EntryCheck™ programming options. For
most installations, the factory set default options are sufficient.
The keypad must be in Programming Mode to make these
changes.
Programming the 923 To Hold the Output
SDC's EntryCheck™ products have a programmable "Toggle
Mode" available for each relay and solid-state output. When an
output is programmed for Toggle Mode, the output alternates from
OFF to ON or from ON to OFF each time it is activated. When
output is toggled on, the green LED remains solid until toggled off.
The rules for a toggle output are:
If the output is OFF, it will turn ON and stay on until the next
activation.
If the output is ON, it will turn OFF and stay off until the next
activation.
An authorized PIN, Card, or REX input programmed to
momentarily activate that same relay will reset the relay to its
normal state.
Advertisement
