Download
Share
Print this page
  1. Manuals
  2. Brands
  3. WaterRower Manuals
  4. Home Gym
  5. Indo-row A1
  6. Assembly manual

WaterRower Indo-row A1 Assembly Manual

Hide thumbs Also See for Indo-row A1:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Main Parts
A
Mono Rail Assembly (with seat)
B
Tank Assembly
C
Sub Rails × 2
D
Footboard
Other Parts
E
JCB 23mm (WRB-B700) × 8
F
JCN (WRP-B711) × 8
G
Handle Rest (WRP-P430) × 2
H
Handle Rest Bolt (WRP-P455) × 2
I
Clamp Bar Bolt (WRP-P1140) × 1
J
Rail Sub Bracket Bolt (WRP-S210) × 1
K
Back of Footboard Bolt (WRP-B720) × 4
L
Rail Sub Bracket (WRP-R1500) × 1
M
5mm Allen Key (WRP-B740) × 1
N
Heel Rests (WRP-P1700) × 2
O
Syphon Pump (WRP-B405) × 1
P
Chlorine Tablets (WRP-B960) × 3
Assembly mAnuAl
A
b
with
C
e
G
I
K
m
O
D
F
H
J
l
n
P

Advertisement

loading

Related Manuals for WaterRower Indo-row A1

Summary of Contents for WaterRower Indo-row A1

  • Page 1 with Assembly mAnuAl Main Parts Mono Rail Assembly (with seat) Tank Assembly Sub Rails × 2 Footboard Other Parts JCB 23mm (WRB-B700) × 8 JCN (WRP-B711) × 8 Handle Rest (WRP-P430) × 2 Handle Rest Bolt (WRP-P455) × 2 Clamp Bar Bolt (WRP-P1140) × 1 Rail Sub Bracket Bolt (WRP-S210) ×...
  • Page 2 Step 1 Lay the sub rails on the floor with ends parallel. Dolly wheels on the outside. Attach the end of the mono rail to the angled ends of the sub rails with the Allen key (M) and 4 pairs of the JCN nuts (F) and JCB bolts (E) . Do not tighten all the way.
  • Page 3 Step 3 Place the footboard on the rails, then attach the sensor cable to the monitor cable protruding from the back of the footboard. The sensor cable may be taped to the back of the footboard. If so, remove the tape. Feed the cable gently through the brackets so it does not get trapped between the footboard and tank assembly.
  • Page 4 Step 5 Tighten the footboard to the mono rail by screwing in the clamp bar bolt (I). Do not tighten all the way. × 1 Step 6 Stand the machine up and insert two of the back of footboard bolts (K) into the footboard bracket.
  • Page 5 Step 8 Screw in the rail sub bracket (L) underneath the footboard using the 2 remaining back of footboard bolts (K). Tighten all the way. × 1 × 2 Step 9 Go back and tighten all the bolts in steps 1, 2, 5, and 6. Also tighten the 4 bolts on the front of the rower (below forward riser bumpers, see tag).
  • Page 6 Step 11 Unwrap the recoil belt from the forward riser bracket, making sure the belt runs below and around the pulley. Attach the D ring on the recoil belt to the bungee hook. Step 12 Lay the unit flat and remove the tank stopper from between the top and bottom deck.
  • Page 7 Information found on the sticker includes the Serial Number (along the top), contact information (middle) and the level gauge (second half). Recommended Water Levels: Level 15 - 16: Beginner Level 16 - 18: Intermediate Level 18 - 19: Advanced WaterRower Do not fill above this line...

  • Page 8: Troubleshooting Tips

    Paddle not turning smoothly, loosen all tank bolts and retighten. For other troubleshooting and service tips, please visit www.waterrowerservice. com or contact WaterRower at support@waterrower.com or call 800 852 2210. Notes Make note of the serial number. This number can be found on the level gauge sticker and is required when contacting WaterRower for customer support.