Wilo -HiMulti 3 H Series Installation And Operating Instructions Manual
Hide thumbs
Also See for Wilo-HiMulti 3 H Series:
- Installation and operating instructions manual (102 pages) ,
- Installation and operating instructions manual (100 pages)
Advertisement
Advertisement
Table of Contents
Related Manuals for Wilo Wilo-HiMulti 3 H Series
Summary of Contents for Wilo Wilo-HiMulti 3 H Series
- Page 1 Pioneering for You Wilo-HiMulti 3 H... Wilo-HMHI Wilo-Jet HWJ de Einbau- und Betriebsanleitung en Installation and operating instructions Notice de montage et de mise en service Inbouw- en bedieningsvoorschriften ru Инструкция по монтажу и эксплуатации 2 544 452-Ed.01 / 2016-01-Wilo...
- Page 2 Fig. 1: Fig. 2:...
- Page 3 Fig. 3a: 1~230V /50Hz...
- Page 4 Fig. 3b: 1~230V /50Hz...
- Page 5 Fig. 3c: 1~230V /50Hz...
- Page 6 Fig. 4: Fig. 5a:...
- Page 7 Fig. 5b: Fig. 6a: Fig. 6b: BN BU GNYE BN BU GNYE WJ Jetson MHI Multi-H...
- Page 8 Fig. 6c: Fig. 6d: PE N GNYE GNYE GNYE HiMulti3 Claris Home Fig. 7a: Fig. 7b: GNYE BK BN BU GNYE BK BN BU GNYE BK BN BU GNYE...
- Page 9 Fig. 8a: Fig. 8b: pa [bar] pa [bar] Fig. 9a: Fig. 9b: Fig. 9c:...
- Page 10 Fig. 10a: GNYE 17 19 GNYE GNYE Fig. 10b: GNYE...
- Page 11 Electrical connection............................25 Commissioning .............................26 Check the diaphragm pressure vessel........................26 Filling and venting ..............................27 Setting the pressure switch ..........................27 Checking the direction of rotation of the motor ....................30 Commissioning..............................30 Decommissioning..............................30 Maintenance............................30 Faults, causes and remedies........................31 Spare parts ............................32 WILO SE 01/2016...
- Page 12 [bar] Start-up pressure Fig. 9a Checking gas supply pressure for diaphragm to 9c pressure vessel Fig. 9a Depressurise system Fig. 9b Remove valve flap Fig. 9c Measure gas supply pressure Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
- Page 13 Fig. 10b HiMulti3 connection diagram for optional float switch (low water cut-out switch) Pressure switch Optional float switch Additional connection terminals HiMulti3 motor terminal box with Quick-Connector Cable BN Brown colours BU Blue BK Black GNYE Green-Yellow WILO SE 01/2016...
-
Page 14: General Information
Children should be supervised to ensure that they do not play with the appliance. Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ... -
Page 15: Transport And Interim Storage
The use of other Use with other fluids or additives requires parts will absolve us of liability for consequential approval from Wilo. events. DANGER! 2.8 Improper use Risk of explosion! This domestic water system... -
Page 16: Product Information
100 litre tank Ô 310 x 248 mm Fastening screws required 4 x Ø8 mm (20 L and 100 L tank) or 4 x Ø6 mm (50 L tank) See dimension drawing/catalogue/data sheet for further dimensions Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ... -
Page 17: Description And Function
(Figs. 1 and 2, item 7) and a diaphragm pressure vessel (Figs. 1 and 2, item 4). The pump increases the pressure and pumps the fluid to the extraction points via the consumer WILO SE 01/2016... - Page 18 H07 RNF acc. to DIN 57282 or from the base of the tank and a minimum water DIN 57245. coverage of 200 mm at the lowest possible water level. Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
- Page 19 1 bar = 100000 Pa = 0.1 MPa = 0.1 N/mm² sel in relation to the switch-on pressure pI = 10200 kp/m² = 1.02 kp/cm² (at) 1 bar = 0.987 atm = 750 Torr = 10.2 m/Ws WILO SE 01/2016...
- Page 20 (adjusting screw Fig. 7a/7b, item b) are set in rela- (closed stop valve). tion to the switch-on pressure at the pressure switch (DM version). The following diagram describes the procedure for setting the pressure switches. Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
- Page 21 Increase difference between switch-on pressure and switch-off pressure (routine 3) Establish electrical power supply and check the settings using the values displayed on the pressure gauge Mount the pressure switch cover WILO SE 01/2016...
- Page 22 Turn switch-off pressure adjusting screw anticlockwise until a clicking sound can be heard Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
-
Page 23: Maintenance
• Disconnect the domestic water system from the Wilo customer service for checks and repairs. mains. DM version: Switch on briefly and verify that the • Close the inlet side shut-off device (Fig. 3a, 3b direction of rotation of the pumps (look at the fan or 3c, item 11). - Page 24 Cable terminals loose Check cable terminals of the motor and secure Pump not adequately secured to the Tighten fastening screws tank Bearing surface is not solid enough Stabilise the bearing surface Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
-
Page 25: Spare Parts
11 Spare parts Spare parts may be ordered via a local installer and/or Wilo customer service. To avoid queries and incorrect orders, all data from the rating plate must be specified with every order. Subject to change without prior notice. - Page 26 English Installation and operating instructions Wilo domestic water systems HiMulti3..H.. /HMHI/HWJ...
- Page 29 WILO SE Nortkirchenstraße 100 D-44263 Dortmund Germany T +49(0)231 4102-0 F +49(0)231 4102-7363 wilo@wilo.com Pioneering for You www.wilo.com...
Need help?
Do you have a question about the Wilo-HiMulti 3 H Series and is the answer not in the manual?
Questions and answers