Related Manuals for Perle IOLAN SDG1 W
Summary of Contents for Perle IOLAN SDG1 W
- Page 1 IOLAN SDG1 W Hardware Installation Guide Updated: Sept. 1,2019 Version A.1-09.01.2019 Document Part#:5500412-10(Rev C) www.perle.com...
- Page 2 Modifications to this product not authorized by Perle could void the FCC approval and negate your authority to operate the product. Perle reserves the right to make changes without further notice, to any products to improve reliability, function, or design.
-
Page 3: Table Of Contents
Contacting Perle Systems Limited ........ -
Page 4: Hardware
Preface Audience This guide is for the network or computer technician responsible for installing the Perle IOLAN SDG1 W. Familiarity with the concepts and terminology of Ethernet and local area networks is required. Purpose This document describes the hardware and physical characteristics of the Perle IOLAN SDG1 W. -
Page 5: Overview
Overview This guide provides information on installing and doing the initial configuration on the IOLAN SDG1 W unit. The IOLAN SDG1 W has one DB9 serial port. IOLAN SDG1 W (Top View) IOLAN SDG1 W Hardware Installation Guide... -
Page 6: Iolan Sdg1 W (Side Views)
1000 Mbps through twisted pair (UTP) cables of up to 100 meters (328ft) in length. Console / Serial Port The IOLAN SDG1 W has one DB-9 serial port. The serial port can be used to connect a serial device or a console. When used to connect a serial device, the port can operate in EIA-232, EIA-422 or EIA-485 mode. - Page 7 Insert a paper clip into the inset hole labeled as “WPS” and gently press inwards. Pressing this button for less than 3 seconds will put the IOLAN SDG1 W in WPS mode, greater than 4 seconds will put the unit in Soft-AP mode.
-
Page 8: Led Indicators
The first LED within the signal strength display will pulse amber on and off Soft-AP Mode (Access Point Mode) State Description Green - flashing The third LED within the signal strength display will pulse green on and off IOLAN SDG1 W Hardware Installation Guide... -
Page 9: Ethernet Port Status Indicators
Ethernet Port Status Indicators Port Link / Speed State Description Green 1000 Mbps (flashes with activity) Green/Amber 100 Mbps (flashes with activity) Amber 10 Mbps (flashes with activity) No LAN connection IOLAN SDG1 W Hardware Installation Guide... -
Page 10: Installation
Warning: Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment. IOLAN SDG1 W Hardware Installation Guide... -
Page 11: Connecting The Hardware
Connecting the barrel connector Plug the power adapter into a power socket and connect the barrel connector end into the IOLAN SDG1 W. The IOLAN SDG1 W will perform a power up sequence. The Power/ Ready LED should show a solid green. See LED Indicators for power up sequence. -
Page 12: Connecting The Serial Port
1. Set the “console/serial DIP switch” to the console (down) position. 2. Connect an DB9 cable directly from the IOLAN SDG1 W to the COM port on your PC. 3. Choose Start > Control Panel > Systems or equivalent on the Windows Operating System you are using. -
Page 13: Connecting Data Ports
10/100/1000 RJ45 port on the network hub/switch. 2. Once the IOLAN SDG1 W is connected and the link is established, the link LEDs will turn on. These LEDs will indicate whether you have a 10, 100 or 1000 Mb/s link to your hub/switch. -
Page 14: Operation
To reset the IOLAN insert a paper clip into the inset hole labelled as “Reset” and gently press inwards. The Power/Ready LEDs on the IOLAN SDG1 W will go On and then momentarily Off when released to show that the unit has been reset. -
Page 15: Appendix A - Technical Specifications
Storage Temperature -40°C to 85°C -40°F to 185°F Operating and Storage 5 to 95% (non condensing) Humidity Weight 0.25 Kg (0.55lbs) Dimensions 90 by 76 by 24 mm 3.5 by 3.0 by 0.9 in IOLAN SDG1 W Hardware Installation Guide... -
Page 16: Appendix B - Mechanical Drawing
Appendix B - Mechanical Drawing IOLAN SDG1 W Hardware Installation Guide... -
Page 17: Appendix C - Sample Label
Appendix C - Sample Label IOLAN SDG1 W Hardware Installation Guide... -
Page 18: Appendix D - Cabling And Connectors
Mode DB9M Connector DB9M pinouts EIA 422/485 RS485 Pinout RS232 Full Duplex Half Duplex 1 (in) 2 (in) RxD+ 3 (out) TxD- TxD-/RxD- 4 (out) 6 (in) 7 (out) TxD+ TxD+/RxD+ 8 (in) RxD- IOLAN SDG1 W Hardware Installation Guide... - Page 19 Note: For EIA-232 these switches must be in the OFF position (default) Ethernet Cable The 10/100/1000BaseT(X) port is located on the back of the IOLAN SDG1 W. This Ethernet port will automatically adjust depending on the type of Ethernet cable used (straight- through or cross-over), and the type of device (NIC-type or HUB/Switch-type) connected to the port.
-
Page 20: Appendix E - Iolan Maintenance
Appendix E - IOLAN Maintenance • Ensure there is clearance of 50.8mm (2 inches) on all sides of the IOLAN SDG1 W to provide proper airflow through the unit • Do not use solvents or cleaning agents on this unit •... -
Page 21: Contacting Perle Systems Limited
Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. https://www.perle.com/support_services/support_request.shtm Warranty / Registration This product is covered by the Perle IOLAN SDG Warranty. Details can be found at: https://www.perle.com/support_services/warranty.shtml IOLAN SDG1 W Hardware Installation Guide...
Need help?
Do you have a question about the IOLAN SDG1 W and is the answer not in the manual?
Questions and answers