Table of Contents
Advertisement
Quick Links
______________________________________________________________
This guide covers basic installation and configuration and is intended for first time
setup or product evaluation.
Complete details can be found in the following guides at www.perle.com/downloads.
IOLAN User's Guide
IOLAN Command Line Interface Reference Guide
IOLAN SDG4 W Hardware Installation Guide
What's in the box?
The IOLAN SDG4 W
Quick Start Guide (this document)
2 X RP SMA antennae
Power adapter, strain relief strap and rubber feet
Wall mount brackets
Hardware Overview
IOLAN SDG4 W Quick Start Guide ‐ P/N 5500416‐10 (Rev C)
IOLAN SDG4 W
Quick Start Guide
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Perle IOLAN SDG4 W
Summary of Contents for Perle IOLAN SDG4 W
- Page 1 IOLAN SDG4 W Quick Start Guide ______________________________________________________________ This guide covers basic installation and configuration and is intended for first time setup or product evaluation. Complete details can be found in the following guides at www.perle.com/downloads. IOLAN User’s Guide IOLAN Command Line Interface Reference Guide IOLAN SDG4 W Hardware Installation Guide What’s in the box? The IOLAN SDG4 W Quick Start Guide (this document) 2 X RP SMA antennae Power adapter, strain relief strap and rubber feet Wall mount brackets Hardware Overview IOLAN SDG4 W Quick Start Guide ‐ P/N 5500416‐10 (Rev C)
- Page 2 Connecting the Hardware Power Either the barrel or TB(Terminal Block) can be used to power the IOLAN SDG4 W. Connecting the barrel connector Plug the power adapter into a power socket and connect the barrel connector end into the IOLAN SDG4 W. The Power/Ready LED should show a solid green. Connecting the terminal block connector 1. Ensure power is NOT applied to the wires prior to connection. 2. On each end wire (12‐20 AWG), remove the insulation from the copper wire 5 mm (3/16 of an inch). 3. Loosen the left screw on the top of the terminal connector block, then insert ...
- Page 3 then insert your negative (‐) wire into the right terminal and screw it down tight (.51Nm torque). 4. Re‐insert the terminal block connector if removed. 5. Connect the power cord strain relief, if desired. See IOLAN SDG4 W Hardware Guide for details. 6. Connect the grounding lug (not provided) to the grounding screw, if desired. See IOLAN SDG4 W Hardware Installation Guide for details. Connecting the Antennas, Ethernet cable and serial device 1. Connect the Wi‐Fi antenna by simply screwing the antenna onto the connectors on the IOLAN. 2. Connect the Ethernet cable (Cat5/5e) from the RJ‐45 plug (10/100/1000) to the HUB or switch that will provide network connectivity (if applicable to your application). 3. Connect the serial devices to the serial ports. See the SDG4 W Hardware Installation Guide for pinout details. Turn on power at source. Power-on Cycle When the power is connected to the IOLAN SDG4 W, the Power/Ready LED will cycle through several sequences and will end in a solid green once the unit is fully booted and ready to be configured. If the LED is not solid green after two minutes, see IOLAN SDG4 W Hardware Installation Guide. LED Guide System Ready Green solid—System Ready Green flashing—System is booting or DIP switch is in console mode Yellow flashing—Booting Red—Error condition. See IOLAN SDG4 W Hardware Installation Guide ...
- Page 4 The IOLAN SDG4 W is listed on your network connections on your PC or wireless client. It will appear as SSID: IOLAN‐xxxxxx (the last 6 digits of the IOLAN wireless MAC address ‐ found on the product label). Select this SSID on the PC. When a password is requested, enter the password printed on the product label. You should now be connected to the IOLAN’s Wireless interface. Use a Web browser to connect to the default address of the IOLAN SDG4 W at (192.168.0.1). The default userid is “admin” and the default password is “superuser” (case sensitive). You can now configure and manage your IOLAN SDG4 W using the IOLAN WebManager application. Note: You should change the admin password to restrict unauthorized access to your IOLAN. For additional methods of configuring your IOLAN (i.e., Device Manager, Telnet, SNMP), please refer to the IOLAN User’s Guide. Registering the IOLAN You should register IOLAN online at: www.perle.com/support_services/warranty_reg.asp Contacting Technical Support Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. www.perle.com/support_services/support_request.shtm IOLAN SDG4 W Quick Start Guide ‐ P/N 5500416‐10 (Rev C) 4 ...
Need help?
Do you have a question about the IOLAN SDG4 W and is the answer not in the manual?
Questions and answers