Quadra-Fire CB1200I-C Owner's Manual
  1. Manuals
  2. Brands
  3. Quadra-Fire Manuals
  4. Indoor Fireplace
  5. CB1200I-C
  6. Owner's manual

Quadra-Fire CB1200I-C Owner's Manual

Hide thumbs Also See for CB1200I-C:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions on installation, operation, or service.
NOTICE: DO NOT DISCARD THIS MANUAL
CB1200 PELLET INSERT
APPLIANCE
MODEL:
CB1200I-C
CAUTION
Tested and approved for wood pellets and corn pellets.
Burning of any other type of fuel voids your warranty.
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
1
Owner's Manual
Operation & Care
R
7027-805C
WARNING
If the information in these instructions is
not followed exactly, a fire could result
causing property damage, personal injury,
or death.
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
•
Do not over fire - If appliance or chimney connector
glows, you are over firing. Over firing will void
your warranty.
•
Comply with all minimum clearances to combustibles
as specified. Failure to comply may cause house fire.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
•
Do not touch glass until it is cooled
•
NEVER allow children to touch glass
•
Keep children away
•
CAREFULLY SUPERVISE children in same room
as fireplace.
•
Alert children and adults to hazards of
high temperatures
•
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other
flammable materials away.
CAUTION
Check building codes prior to installation.
•
Installation MUST comply with local, regional, state
and national codes and regulations.
•
Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
NOTE: To obtain a French translation of this
manual, please contact your dealer or visit
www.quadrafire.com
REMARQUE : Pour obtenir une traduction française de
ce manuel, s'il vous plaît contacter votre
revendeur ou visitez
www.quadrafire.com
June 4, 2019

Advertisement

Table of Contents
loading

Related Manuals for Quadra-Fire CB1200I-C

Summary of Contents for Quadra-Fire CB1200I-C

  • Page 1 MODEL: other appliance. • Do not over fire - If appliance or chimney connector CB1200I-C glows, you are over firing. Over firing will void your warranty. • Comply with all minimum clearances to combustibles as specified.

  • Page 2: Sample Of Serial Number / Safety Label

    CB1200 Pellet Insert and Welcome to the Quadra-Fire Family NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction A. Sample of Serial Number / Safety Label LOCATION: On chain behind right access panel & Behind left access panel CAUTION: HOT WHILE IN OPERATION DO NOT TOUCH.

  • Page 3: Table Of Contents

    T. Thermostat Battery Replacement ... . . 16 U. Frequently Asked Questions ....17 Quadra-Fire is a registered trademark of Hearth & Home Technologies. June 4, 2019...

  • Page 4: Warranty Policy

    CB1200 Pellet Insert B. Warranty Policy Hearth & Home Technologies LIMITED LIFETIME WARRANTY Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet and electric hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: WARRANTY PERIOD: distributor, whichever occurs earlier.
  • Page 5 CB1200 Pellet Insert WARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites. • • This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides. •...
  • Page 6 CB1200 Pellet Insert This warranty is void if: • • • There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited LIMITATIONS OF LIABILITY • have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN.

  • Page 7: Listing And Code Approvals

    CB1200 Pellet Insert Listing and Code Approvals A. Appliance Certification B. BTU & Efficiency Specifications Emissions Report #: 0061PN013E Model CB1200 Pellet Insert EPA Certification #: 171-19 Laboratory OMNI Test Laboratories, Inc. EPA Certified Emissions: 0.8 grams per hour Safety 061-S-13-2 Report No.

  • Page 8: Mobile Home Approved

    CB1200 Pellet Insert C. Mobile Home Approved WARNING • This appliance is approved for mobile home installations when not installed in a sleeping room and Fire Risk. when an outside combustion air inlet is provided. Hearth & Home Technologies disclaims any •...

  • Page 9: Operating Instructions

    CB1200 Pellet Insert User Guide Operating Instructions Fuel Material WARNING • Made from sawdust or wood by-products • Depending on the source material it may have a high or low ash content. Higher Ash Content Material Fire Risk. • Do not operate appliance before reading •...

  • Page 10: Before Your First Fire

    CB1200 Pellet Insert Moisture F. Filling the Hopper Always burn dry fuel. Burning fuel with high moisture Open the hopper lid by lifting the handle. Fill the hopper content takes heat from the fuel and tends to cool the with fuel. Close the hopper lid. The unit will not feed with appliance, robbing heat from your home.

  • Page 11: Starting Your First Fire

    CB1200 Pellet Insert J. Feed Rate Adjustment Instructions H. Starting Your First Fire The feed adjustment control rod is factory set, and should 1. A thermostat is required for proper operation of this be adequate for most fuels. The set screw is located at the appliance.

  • Page 12: Ignition Cycles

    CB1200 Pellet Insert K. Ignition Cycles M. Restarting the Appliance Restart Process 1. During each ignition cycle, it is normal to see some smoke in the firebox. The smoke will stop once the 1. When the unit has run out of fuel, add pellet fuel to fire starts.

  • Page 13: Thermostat Controls

    CB1200 Pellet Insert O. Thermostat Controls P. Thermostat Setup Options TEMPERATURE (HEAT / OFF) SWITCH: Setup options for how the thermostat will function are Set this switch to Heat to control your appliance. The off performed using a menu on the display screen. position will disable the appliance.

  • Page 14: Thermostat Operation Instructions

    CB1200 Pellet Insert ITEM #08 (TEMPERATURE DIFFERENTIAL): TEMPERATURE HOLD: • The thermostat works by turning your heating system Temperature hold is used for maintaining a fixed set on and off whenever the room temperature varies from temperature; once a hold is initiated, the thermostat will the desired set-point temperature.

  • Page 15: Thermostat Other Features

    CB1200 Pellet Insert COPY PROGRAM FEATURE: KEYPAD LOCKOUT: Using similar instructions as set temperature programs the There is the option to lock the front panel buttons to prevent COPY button will allow a whole day of set program events unauthorized tampering of your thermostat settings. to be copied to another day.

  • Page 16: Thermostat Battery Replacement

    CB1200 Pellet Insert T. Thermostat Battery Replacement CONNECT THERMOSTAT WIRES TO APPLIANCE: There is a 4 screw terminal block located on the back This thermostat is powered by two “AA” Alkaline batteries. lower left corner of the stove directly above the power The batteries should be replaced AT LEAST once per cord inlet.

  • Page 17: Frequently Asked Questions

    CB1200 Pellet Insert U. Frequently Asked Questions What causes my glass to become dirty? If the glass has white ash build up it is normal and the glass should be cleaned. If it is a black soot build up airflow through the unit may be restricted.

  • Page 18: Maintenance And Service

    CB1200 Pellet Insert Maintenance and Service When properly maintained, your fireplace will give CAUTION you many years of trouble-free service. Contact your dealer to answer question regarding proper operation, Shock and Smoke Hazard troubleshooting and service for your appliance. Visit •...

  • Page 19: General Maintenance And Cleaning

    CB1200 Pellet Insert C. General Maintenance and Cleaning 1. Types of Fuel Type of fuel you are burning will dictate how often you have to clean your fire pot. If the fuel you are burning has a high dirt or ash content or you are burning shelled field corn, it may be necessary to clean the fire pot more than once a day.
  • Page 20 CB1200 Pellet Insert 5. Disposal of Ashes 7. Cleaning Heat Exchanger Chambers & Drop Tube • Frequency: As needed • Frequency: Weekly or every 1 ton of fuel • By: Homeowner • By: Homeowner Ashes should be placed in a metal container with a The amount of ash buildup in the firebox will be a good tight-fitting lid.
  • Page 21 CB1200 Pellet Insert 9. Cleaning Exhaust Path 11. Door Latch Inspection • Frequency: Yearly or more frequently depending on • Frequency: Prior to heating season ash build-up. • By: Homeowner • By: Homeowner The door latch is non-adjustable but the gasket between a.
  • Page 22 CB1200 Pellet Insert 19. Clean Firebox Exhaust Exits & Exhaust Blower a. There are 2 exhaust exits at the back of the firebox on 16. Preparing Firebox for Non-Burn Season the left and right side (Figure 22.1). • Frequency: At the end of the heating season b.

  • Page 23: Soot Or Creosote Fire Awareness

    CB1200 Pellet Insert D. Soot or Creosote Fire Awareness E. High Ash Fuel Content Maintenance • Frequency: When the ash build-up exceeds more than The chimney should be inspected periodically during the heating season to determine if a creosote build-up has half way up the fire pot.

  • Page 24: Troubleshooting Guide

    CB1200 Pellet Insert Troubleshooting Guide With proper installation, operation, and maintenance your appliance will provide years of trouble-free service. If you do experience a prob- lem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
  • Page 25 CB1200 Pellet Insert SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Feed system fails to start. Out of fuel. Check hopper, fill with fuel. #2 snap disc may be defective. Replace snap disc. Firebox door must be closed securely. Vacuum switch not closing. No vacuum. Check exhaust blower is plugged in and operating.

  • Page 26: Service Parts Replacement

    CB1200 Pellet Insert Service Parts Replacement A. Blower Replacement 1. Combustion (Exhaust) Blower Replacement Blower Mounting Screws Housing Bolts PART NUMBER: 812-3381 b. Prep appliance from the blower removal: iii. Disconnect the appliance from the electrical outlet. iv. Remove panel set and disconnect flue. Pull appliance out onto the hearth.

  • Page 27: Baffle Replacement

    CB1200 Pellet Insert B. Baffle Replacement C. Igniter Replacement PART NUMBER: SRV7000-462 PART NUMBERS: LEFT BAFFLE: 812-4200 a. Be sure the appliance is allowed to cool, has been RIGHT BAFFLE: 812-4210 unplugged and the exhaust blower is off. Remove the ash pan.

  • Page 28: Glass Replacement

    CB1200 Pellet Insert D. Glass Replacement 2. Replacing Side Glass WARNING NOTE: When removing the side glass with the door latch, you must remove the door latch first before • Glass is 5mm thick high temperature removing the side frame. Use a powered Phillips heat-resistant ceramic glass.

  • Page 29: Reference Materials

    CB1200 Pellet Insert Reference Materials When describing the location of a component, it is always A. Component Function AS YOU FACE THE FRONT OF THE APPLIANCE. 1. Control Box a. The control box is located on right side of 7. Heat Exchangers appliance, behind the right side panel.
  • Page 30 CB1200 Pellet Insert 16. Thermostat 19. Snap Disc #3 (Burn Back Protector) 250°F The appliance is designed to run on a 12 volt AC Snap disc #3 is mounted on the right side of the auger thermostat. The heat anticipator, if present, should be tube just below feed motor and has a reset button.

  • Page 31: Component Locations

    CB1200 Pellet Insert B. Component Locations Cleaning Rods Terminal Block Center 2 Screws for Thermostat Wires Control Box Heat Output Switch Reset Button Blue Blinking Red Call Light Light Fuse Red/ Green Light Power Outlet Heat Exchanger Tubes Figure 31.1 Figure 31.2 Exhaust Transition...

  • Page 32: Service & Maintenance List

    CB1200 Pellet Insert C. Service & Maintenance List Date of Service Performed By Description of Service 7027-805C June 4, 2019...
  • Page 33 CB1200 Pellet Insert Date of Service Performed By Description of Service June 4, 2019 7027-805C...

  • Page 34: Exploded Drawing

    CB1200 Pellet Insert D. Exploded Drawing CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active Classic Bay Pellet Insert Part number list on following pages. 06/19 7027-805C June 4, 2019...

  • Page 35: Service Parts

    CB1200 Pellet Insert E. Service Parts CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Stocked Hearth and Home Technologies does not sell directly to consumers distributor.
  • Page 36 CB1200 Pellet Insert CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Stocked Hearth and Home Technologies does not sell directly to consumers distributor.
  • Page 37 CB1200 Pellet Insert CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Stocked Hearth and Home Technologies does not sell directly to consumers distributor.

  • Page 38: Accessories

    CB1200 Pellet Insert F. Accessories CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Stocked Hearth and Home Technologies does not sell directly to consumers distributor.
  • Page 39 CB1200 Pellet Insert CB1200I-C Service Parts Beginning Manufacturing Date: May 2019 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Stocked Hearth and Home Technologies does not sell directly to consumers distributor.
  • Page 40 Hearth & Home Technologies 352 Mountain House Road Halifax, PA 17032 Division of HNI INDUSTRIES Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer log onto www.quadrafire.com CAUTION DO NOT DISCARD THIS MANUAL...

Table of Contents