1. Manuals
  2. Brands
  3. Smith & Noble Manuals
  4. Racks & Stands
  5. Metro Track Flat Aluminum Hardware
  6. Installation instructions manual

Smith & Noble Metro Track Flat Aluminum Hardware Installation Instructions Manual

Wall mount bay single rod set
Hide thumbs Also See for Metro Track Flat Aluminum Hardware:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version

Warranty Service

The enjoyment of your hardware should be everlasting, which is why our products
come with a limited lifetime warranty. The warranty applies to the original owner,
requires a proof of purchase (hang on to your receipt!) and covers defects in material
or craftsmanship. Hardware must have been properly installed. We reserve the right to
determine if your hardware warrants a repair or a replacement. Visit smithandnoble.
com/guarantee to see full details. In need of warranty service? Call us at 800.248.8888
and we'll arrange for a repair or replacement ASAP.
© 2019 Smith & Noble Home, Inc. All Rights Reserved
STEP BY STEP INSTALLATION INSTRUCTIONS
Metro Track
Flat Aluminum
Hardware
SN0419
Wall Mount
Bay Single Rod Set

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Metro Track Flat Aluminum Hardware and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Smith & Noble Metro Track Flat Aluminum Hardware

Summary of Contents for Smith & Noble Metro Track Flat Aluminum Hardware

  • Page 1 STEP BY STEP INSTALLATION INSTRUCTIONS Metro Track Flat Aluminum Hardware Warranty Service The enjoyment of your hardware should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase (hang on to your receipt!) and covers defects in material or craftsmanship.
  • Page 2 Everything Table of Contents You Need Getting Started ........3 Step 1 - Wall Mount Bay Single Rod Set .

  • Page 3: Getting Started

    STEP 1 - GETTING STARTED OVERVIEW Getting Started Wall Mount Bay Single Rod Set Before you begin, check the accompanying diagram to make sure you have all the parts you need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough to accommodate the brackets.
  • Page 4 STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS Place center of bracket cover plate Mounting the Brackets Figure A level against wall at the marked spots. Place the panel on one of the rods. Using a pencil, lightly draw a circle To ensure it drapes at the correct around the base of the bracket onto length, hold it up to the spot you...
  • Page 5 STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - PLACING CARRIERS & END STOPS Adding or Removing Carriers to the Rod Depending on your order, you may have CARRIERS END STOP Your track rods will come with all master ROD CONNECTOR received a rod connector.
  • Page 6 STEP 5 - ATTACHING BRACKET TO THE POSTS STEP 6 - ATTACHING FINIALS END CAP FINIALS Insert the mounting posts into the channel MOUNTING Slide in End Cap onto rod and tighten POST CHANNELS set screw. in the back of the track. Do not tighten at MOUNTING this time.
  • Page 7 STEP 7 - ATTACHING ELBOW OR 90º BRACKET STEP 8 - ATTACHING BRACKET POSTS TO BRACKET BASES Elbow ° Corner or Elbow Bracket 90° Corner Bracket Align the mounting posts in the back of Slide in bracket or elbow into the end of MOUNTING the left rod with the brackets mounted the left rod where there is no finial end...
  • Page 8 STEP 9 - ATTACHING DRAPERY TO ROD ACCESSORIES CLIP Insert drapery pin hooks into carriers Baton/Wand (optional) and master carriers. Baton/Wand will be pre-attached to the Split Drapery master carrier(s). For Split drapery, start pining from the center and go towards the ends. MASTER DR APERY CARRIER...

Table of Contents