Smith & Noble Metro Track Flat Aluminum Hardware Installation Instructions Manual

Ceiling mount double rod set
Hide thumbs Also See for Metro Track Flat Aluminum Hardware:

Advertisement

Quick Links

Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to the
original owner, requires a proof of purchase (hang on to your receipt!) and
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we'll arrange for a repair
or replacement ASAP.
© 2019 Smith & Noble Home, Inc. All Rights Reserved
STEP BY STEP INSTALLATION INSTRUCTIONS
Metro Track
Flat Aluminum
Hardware
SN0419
Ceiling Mount
Double Rod Set

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Metro Track Flat Aluminum Hardware and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Smith & Noble Metro Track Flat Aluminum Hardware

  • Page 1 STEP BY STEP INSTALLATION INSTRUCTIONS Metro Track Flat Aluminum Hardware Warranty Service The enjoyment of your hardware should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase (hang on to your receipt!) and covers defects in material or craftsmanship.
  • Page 2: Table Of Contents

    Everything Table of Contents You Need Getting Started ........3 Step 1 - Ceiling Mount Double Rod Set .
  • Page 3: Step 1 - Getting Started

    STEP 1 - GETTING STARTED OVERVIEW Tools & Parts Ceiling Mount Double Rod Set Before you begin, check the accompanying diagram to make sure you have all the parts you need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough to accommodate the brackets.
  • Page 4: Step 2 - Marking Bracket Placement

    STEP 2 - MARKING BRACKET PLACEMENT STEP 3 - ATTACHING THE ROD CONNECTOR Back Rod Back rod 2" away from 2" wall or window. Depending on your order, you may ROD CONNECTOR Place the back panel on the back rod. have received a rod connector.
  • Page 5 STEP 4 - ADDING OR REMOVING CARRIERS STEP 4 - ADDING OR REMOVING CARRIERS Front Rod Back Rod CARRIERS Your track rod will come with all master Your track rod will come with all master carriers and regular carriers pre-installed. carriers and regular carriers pre-installed.
  • Page 6 STEP 4 - ADDING OR REMOVING CARRIERS STEP 4 - ADDING OR REMOVING CARRIERS Back Rod Back Rod SPLIT DRAPERY (A) ONE WAY DRAW DRAPERY (B) Split Draw BACK One Way Draw Once all carriers have been For one way draw drapery, place End stop &...
  • Page 7: Step 5 - Attaching Bracket To Front Rod

    STEP 5 - ATTACHING BRACKET TO FRONT ROD STEP 6 - ATTACHING FINIALS CEILING BRACKET END CAP FINIALS Slide in End Cap onto rod and tighten CHANNEL Insert the ceiling brackets into the set screw. channel in the back of the track. Do not tighten at this time.
  • Page 8: Step 7 - Attaching Bracket To Ceiling

    STEP 7 - ATTACHING BRACKET TO CEILING STEP 8 - ATTACHING BACK ROD TO CEILING BRACKET Back Rod Place the front lip of the rod into the front edge of the clip. Attach the ceiling bracket to the ceiling, Rotate the back of the rod up into aligning the holes of the bracket with the clips and snap into place.
  • Page 9: Step 9 - Attaching Drapery To Rod

    STEP 9 - ATTACHING BRACKET TO CEILING STEP 10 - ATTACHING DRAPERY TO RODS Insert drapery pin hooks into carriers Front Rod and master carriers. Split Drapery Hold the rod up and attach the brack- et to the ceiling, aligning the holes of For Split drapery, start pining from the DRAPERY MASTER...
  • Page 10: Care & Cleaning

    ACCESSORIES CARE & CLEANING Baton/Wand (optional) Minimal care and cleaning is needed to maintain the beauty of your Hardware. Baton/Wand will be pre-attached to To Vacuum: Use brush or dust head attachment. the master carrier(s). To Dust: Use soft, clean cloth. CLIP BATON/ WAND...

Table of Contents