Advertisement
a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the THP0FU is used exceeds
the applicable RF compliance level above, the THP0FU should be observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as reorienting or relocating the THP0FU.
b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Guidance and manufacturer's declaration – electromagnetic immunity
The THP0FU is intended for use in the electromagnetic environment specified below. The customer or the user of the THP0FU should assure that it is
used in such an environment.
Immunity test
Electrostatic
6 kV contact
discharge (ESD)
8 kV air
IEC 61000-4-2
Electrical fast
transient/burst
2 kV for power supply lines
1 kV for input/output lines
IEC 61000-4-4
Surge
1 kV line(s) to line(s)
IEC 61000-4-5
2 kV line(s) to earth
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
interruptions and
(60 % dip in UT)
voltage variations
for 5 cycles
on power supply
input lines
70 % UT
(30 % dip in UT)
IEC 61000-4-11
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
NOTE UT is the a.c. mains voltage prior to application of the test level.
portable and mobile RF communications equipment and the ME EQUIPMENT or ME SYSTEM
The THP0FU is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the
THP0FU can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment
(transmitters) and the THP0FU as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of
transmitter
W
0,01
0,1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the
equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and
people.
IEC 60601 test level
3 A/m
Recommended separation distances between
150 kHz to 80 MHz
d = 1,2
N/A
N/A
N/A
N/A
N/A
Compliance level
6 kV contact
Floors should be wood, concrete or ceramic tile. If floors are covered
8 kV air
with synthetic material, the relative humidity should be at least 30 %.
Mains power quality should be that of a typical commercial or
Not applicable
hospital environment.
Mains power quality should be that of a typical commercial or
Not applicable
hospital environment.
Mains power quality should be that of a typical commercial or
hospital environment. If the user of the THP0FU requires
Not applicable
continued operation during power mains interruptions, it is
recommended that the THP0FU be powered from an
uninterruptible power supply or a battery.
Power frequency magnetic fields should be at levels
3 A/m
characteristic of a typical location in a typical commercial or
hospital environment.
Separation distance according to frequency of transmitter
80 MHz to 800 MHz
d = 1,2
Electromagnetic environment – guidance
m
0,12
0,38
1,2
3,8
12
800 MHz to 2,5 GHz
d = 2,3
0,23
0,73
2,3
7,3
23
Advertisement
