Radiant Innovation TH58F User Manual

TH58F Non contact Forehead Thermometer
Intended use: The infrared forehead thermometer can measure the infrared heat generated by central forehead and
surrounding tissues to reflect patient's body temperature accurately.
Intended operator: At least 11 years old (5 years intensive reading experience), no maximum.
Specifications 
Temperature measurement range:
Forehead mode: 34~42.2°C (93.2~108°F)

Operating temperature range: 10~40°C (50~104°F), 15%~85% RH

Storage temperature range:
It should be stored at room temperature between -20~+50°C, RH≦85%
Transportation temperature shall be less than 70°C, RH≦95%

Atmospheric pressure: 800~1013 hPa

Comply with ASTM E1965-98, EN ISO 80601-2-56, IEC/EN60601-1-2(EMC),
IEC/EN60601-1(Safety) standards, ISO10993, RoHS.

Accuracy:
±0.2°C (0.4°F) within 35~42°C (95~107.6°F), ±0.3°C (0.5°F) for other range.

Fever Indication & Memory locations(with each measurement date/time)

Real time clock, °C / °F Switch mode

Battery: one lithium cell battery (CR2032 *1pcs)

This thermometer converts the forehead temperature to display its "oral equivalent."
(according to the result of the clinical evaluation to get the offset value)

Enclosure Rating: IP22

Dimensions: 127.7 x 41.4 x 36.0 mm

Weight: 65.8 grams including battery

Battery life: around 3,000 continuous readings.

Expected Service Life: 4 years
The device should not submerge into any liquids and expose it to direct moisture.
There is no gender and age limitation for using infrared thermometer.
This is not an AP or APG product.
Functions
The real time clock will be recorded with the memory function and help you to recognize each
Real Time Clock measurement result. (It includes the 12/24 Format_Hour_Minutes_Date.)
 Please see the "Real time clock setting" section to learn how to setup the time in the first use.
Suitable ambient temperature is important for the baby and patient, the thermometer always help you
recognize the room temperature.
Room Temperature
 When in power off, room temperature will always be shown on the screen with
 Please see the "Use of the thermometer" section to learn how to get the correct room temperature.
The thermometer has been designed for practical use. It's not meant to replace a visit to the doctor. Please
Forehead
also remember to compare the measurement result to your regular body temperature.
Temperature
doctor if you have health concerns
 Please see the "Use of the thermometer" section to learn how to measure the body temperature.
If thermometer detects a body temperature ≧37.5°C, there will be a long beep sound followed by three
Fever Indication
short beep sound to warn the user for potential fever.
If thermometer detects a body temperature <37.5°C, there will be " Green" light signal; if temperature
≧37.5°C and < 38.0°C, there will be" Yellow" light signal; if temperature ≧38.0°C, there will be" Red"
light signal.
RED: Continually monitor the body temperature. If in doubt about the person's condition, must seek
Zone Indicator
YELLOW: Continually monitor the body temperature. If in doubt about the person's condition, suggest
GREEN: Normal body temperature.
There are total 9 sets detailed memories with time/date/site for body temperature.
Memory Locations
 When in power on, press the "ON/MEM" button to see the temperature stored with
 In "power off" mode (The LCD only shows the date, time and room temperature). Press and hold the
°C / °F Switch "Start" button, then immediately press and release the "ON/MEM" button. After 3 seconds, icon "°C" will be
switched to icon "°F". (You may use the same way to switch back to "°C")
Real time clock setting
1. Power on: Press the "ON/MEM" button. The thermometer is ready for use after hearing two beep sounds.
2. Press and hold the "ON/MEM" button for 5sec. When you see the Set icon starts flashing, it indicates that you are in the setting screen.(see the following figure.)
3. Press the "Start" button to make the "24" icon flash. This indicates that you are in the 12/24-hour setting screen. Press the "Start" button to set 12/24-hour Format
from "24"(24-hour) to "12"(12-hour).
4. Press "ON/MEM" button to move the flashing in the sequence shown below to select our settings:
hourminutesyearmonthdayleave the setting screen.
5. While the hour, minutes, year, month, day setting is flashing, use "Start" button to change it.
Use of the thermometer
Note: The device must stay in stable ambient (room) temperature for 15 minutes before operating.
1. Always make sure the probe is clean, and without damage.
Warning: Choking from swallowing small parts and batteries by children or pets is possible, please keep small parts and batteries at places
where children and pets can't reach.
medical assistance.
seeking medical assistance.
icon.
Please consult with
icon.
