Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Radiant Innovation TempFairy TN1
Summary of Contents for Radiant Innovation TempFairy TN1
- Page 1 Instruction Manual...
-
Page 2: Table Of Contents
Specifications… … … … … … … … … … … … … … … … … … … … … … … … . … … … .. 13 Contact… … … … … … … … … … … … … … … … … … … … … … … … … … … … … … .. 13 Remarks: Patent Pending Radiant Innovation... -
Page 3: Introduction: Tn1 Series Infrared Thermometer
INTRODUCTION Introduction: TN1 series Infrared Thermometer Thank you for using this Radiant Innovation TN1 series infrared thermometer. TN1 series thermometer is designed with advanced infrared and ambient temperature compensation technology as well as self-diagnoses functions for non-contact, accurate and fast temperature measurements – without waiting. -
Page 4: Parts Description
PARTS DESCRIPTION Parts Description LCD Display Battery Cover Measure Key Mode Key Sensor Stand Key Ring Hole 1. LCD Display 3. Measure Key 5. Sensor 4. Mode Key 2. Battery Cover 6. Stand 7. Key ring Hole Radiant Innovation... -
Page 5: How To Operate
1. Press the “Meas.” key to power on the thermometer. 2. Always keep the sensor lens and the light cone clean before measurement. Please refer to the “Clean and Storage” section for the detail cleaning procedures. Warning: * Proper cleaning of lens to ensures accurate measurements. Radiant Innovation... - Page 6 100 °C boiling pot (aluminum, emissivity~0.3) may show only 50 °C, when you measure the temperature of the aluminum! 4. Power off: Device will automatically shut off if left idle for more than 15sec to extend battery life. Radiant Innovation...
-
Page 7: Unit Switch Between Fahrenheit And Celsius
Depress the mode key again to disable the certain mode. The same procedures will switch the thermometer into the maximum “MAX” mode. In contrary to the minimum mode, the thermometer will pick up and display the maximum temperature of the measuring. Radiant Innovation... - Page 8 “Meas.” key is pressed. There is a metal stand allocated on the rear cover of the thermometer. This stand can keep the thermometer standing on a horizontal surface. This stand is very convenient when using accompany with the “LOCK” mode function. Radiant Innovation...
-
Page 9: Cleaning And Storage
Removing battery cover and replace the battery Follow the clockwise direction to loose the battery cover. Use a pin stick to pick up the old battery. Insert new battery into battery compartment. The battery poles polarity are shown on the battery room. Radiant Innovation... - Page 10 Replace battery with the following battery types. Why restrict the brand? Use of another battery may present a risk of fire or explosion. SONY CR2032 FUJI CR2032 MATSUSHITA CR2032 RADIO SHACK CR2032 RENATA CR2032 VARTA CR2032 AVEREADY/UCAR CR2032 Radiant Innovation...
-
Page 11: Error Messages And Trouble Shooting
0 °C to 40 °C (32 °F to 104 °F). Unload the battery, wait Error5~9, the system is not for 1 minute and repower function properly. it. If the message did not disappear, contact the retailer for further service. Radiant Innovation... - Page 12 Temperature taken is lower Make sure if the target than -22 °C (-7.6 °F). temperature is too low. Please take a new temperature measurement. Device can not be powered on Change with a new to ready stage. battery. Radiant Innovation...
-
Page 13: Specifications
PLASTIC DIMENSION (LxWxH) 68*37*18mm WEIGHT Note: Subject to change without notice. Contact: Ø Contact the nearest retailer if service is needed. Ø Visit the website of Radiant Innovation Inc. (www.raidantek.com.tw) to learn more applications of Infrared Thermometer measurement. Radiant Innovation...