Page 3
The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from devolo. We reserve the right to make any alterations that arise as the result of technical de- velopment.
Magic! te, the device connector, as well as the icons used In no time at all, devolo Magic transforms your on the package: house into a multimedia home that is ready for the future today.
EU, Switzerland and Norway. tips for your device. * The only exceptions are devolo outdoor products, which are suited for the outdoor use thanks to their IP certification. Indicates a completed course of ac-...
Preface 8 Software A printout of the simplified CE declaration of this product is separately included and can also be devolo devices can be used only with the free, found under downloadable programs approved and available www.devolo.com/support/ce. on devolo AG's website (www.devolo.com)
(such as rain or other water). if the devolo device is inoperable. Do not cover devolo devices during operation. if the housing of the devolo device is damaged. Do not place any objects on devolo devices. Do not plug devolo devices directly into each Do not insert any objects into the openings of other.
2.1 devolo Magic Be inspired by products that are astonishingly easy to install, with impressive, innovative technology Home is where devolo Magic is – in no time at all, and unbeatable performance. devolo Magic transforms your house or flat into a...
To set up a devolo Magic network, you need at wiring into a Gigabit LAN Internet access point. least two devolo Magic devices. For technical Its integrated electrical socket can be used (like...
Magic adapters that are in factory default condition, i.e. have been purchased or successfully reset (see Chapter Resetting a devolo Magic ad- apter or removing it from a devolo Magic net- work), automatically start to attempt to pair with another devolo Magic adapter when reconnected to the mains supply.
Page 13
Magic adapter into your existing devolo Magic network. In order to use a new devolo Magic 2 LAN For each pairing operation, only one additional your devolo Magic- network, first you have to devolo Magic adapter can be added at a time.
Red LED Flashes at in- Status 1: Cannot be disabled tervals of 0.5 The reset of the devolo Magic adapter was sec. (on/off) successful. The PLC/reset button has been pressed and held for 10 seconds. Status 2: The devolo Magic adapter (once again) has the factory default settings.
Page 15
The other network nodes are in standby mode and cannot currently be accessed over the mains supply. The PLC LEDs of the other devolo Magic adapters flash white only for a short time. Status 2: The connection to the other network nodes has been interrupted.
Page 16
White Lights up stea- The devolo Magic connection does not have Can be disabled any issues and the devolo Magic adapter is ready to operate. White Flashes at in- The devolo Magic adapter is in standby mo- Can be disabled tervals de.***...
Connecting the devolo Magic 2 LAN 2.3.2Network connection You can use the network connection on the devolo Magic adapter to connect it to a PC or tele- vision using a standard network cable. devolo Magic 2 LAN...
AG reserves the right to change the packa- ge contents without prior notice. This chapter tells you everything you need to know to set up and use your devolo Magic 2 LAN . We 3.2 System requirements describe how to connect the adapter and briefly describe the devolo software.
For ad- ditional technical information on our products, If the LEDs on both devolo Magic adapters refer to the product area at www.devolo.com. light white,...
Magic adapters, the new adapter devolo Magic adapter has been successfully integrated into your Before you can use the devolo Magic 2 LAN existing devolo Magic network. your devolo Magic network, first you have to For each pairing operation, only one additional connect it to your existing devolo Magic adapters adapter can be added at a time.
Ubuntu 13.10 (32-bit/64-bit), from Mac (OS X 10.9) To remove a devolo Magic adapter from your net- You can find the product manual, software and work and successfully restore its entire configurati- additional information on devolo Cockpit onli- on to the factory default settings, press the PLC/ ne at www.devolo.com/cockpit.
You can find more information on devolo soft- browser. Here, you can read out device informati- ware in Chapter 3.4 Installation of devolo on and configure some settings for operating the software.
Page 23
Language selection use. Default settings are identified with an * in drop-down menus. Select the desired language in the language selection list. Default settings can of course be replaced with cu- stomised information. devolo Magic 2 LAN...
MT number: Device type number In the Overview area, you will find information on Serial number: Device serial number hardware and software for the devolo Magic ad- apter and network details. MAC address: MAC address of the device Firmware version: Firmware version of the device...
Page 25
(half/full duplex) are specified; with displaying the following details: otherwise, the status "unconnected" is specified. Device ID: number of the respective devolo Magic adapter in the devolo Magic network LAN – IPv4 DHCP: Display indicating whether DHCP is swit-...
Then, click Start pairing to start the pairing operation. This may take some time. As soon as the new devolo Magic adapter is inte- grated into your existing network, it appears in a list of available and established connections (see Chapter Connections).
Page 27
Get in touch with your internet provider to find out which signal transmission profile is the best To remove a devolo Magic adapter from your option for your internet connection. devolo Magic network, click Leave Powerline network.
Address, Subnetmask, Default gateway and Name server fields. Confirm your settings by clicking the Disk icon. Then, restart the devolo Magic adapter (see Chap- ter 4.2.5 Reboot) to ensure that your changes take effect. IPv6 Configuration...
29 Configuration Confirm your settings by clicking the Disk icon. devolo Magic adapters are to be used and identi- fied in the network. Then, restart the devolo Magic adapter (see Chap- ter 4.2.5 Reboot) to ensure that your changes take effect.
Page 30
Identify Device The devolo Magic adapter can be located using the Identify device function. Click Identify to make the white LED for the corresponding adapter flash for 2 minutes to make it easier to identify by sight.
Page 31
(e.g. computer) is switched on and connected to the network inter- face and if Wi-Fi is disabled. In this mode, the devolo Magic 2 LAN is not accessible over the Powerline network. As soon as the network device (e.g.
Configuration 32 Manually initiate a firmware update Reboot In order to manually update the firmware, To restart a devolo Magic adapter, click Reboot. visit the devolo website (www.devolo.com). Factory Settings Download appropriate file To remove a devolo Magic adapter from your devolo Magic 2 LAN to your computer.
5.1 Technical specifications of the network, we recommend that you comply with the following "connection rules": Security 128 Bit AES Plug the devolo Magic 2 LAN directly into a Device port 1x RJ45 wall socket. Avoid using power strips. This may (Gigabit Ethernet port) impair the transmission of the PLC signals.
5.4 Warranty conditions If your devolo device is found to be defective du- ring initial installation or within the warranty peri- od, please contact the vendor who sold you the product. The vendor will take care of the repair or warranty claim for you.
Page 35
20 DHCP server 28 Disposal of old devices 34 Safety notes 8 Starting up a new devolo Magic network 13 Expanding an existing devolo Magic network 13 Factory default settings 13 Factory reset 13 Integrated electrical socket 17...