Hilti DD AF-CA Operating Instructions Manual
Autofeed units
Hide thumbs
Also See for DD AF-CA:
- Operating instructions manual (51 pages) ,
- Original operating instructions (398 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hilti DD AF-CA
Summary of Contents for Hilti DD AF-CA
- Page 1 DD AF-CA English Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 2 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 3 DD AF-CA Original operating instructions Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 4 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
-
Page 5: Information About The Documentation
Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •... - Page 6 The type designation and serial number are printed on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information...
- Page 7 ▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. ▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Page 8 To achieve a high level of dust collection, use a suitable vacuum extractor of the type recommended by Hilti for wood dust and/or mineral dust and which is designed for use with this power tool. Make sure that the workplace is well ventilated. It is advisable to wear a respirator appropriate for the type of dust generated.
- Page 9 Dirty or dusty machines should thus be checked by Hilti Service at regular intervals, especially if used frequently for working on conductive materials.
- Page 10 Description Parts and operating controls Water flow regulator on the diamond core Control panel and display & drilling machine Drill stand Hose connection to the diamond core Connector for electric power and communi- drilling machine cation Water supply connection Diamond core drilling machine Drilling feed unit English Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 11 Button and LED: Manual mode Intended use The DD AF-CA drilling feed unit, a diamond core drilling machine and a drill stand recommended by Hilti together form an automatic diamond core drilling system suitable for wet core drilling in mineral materials.
-
Page 12: Technical Data
Service indicator Disconnect the system from the electricity sup- The LED lights up ply and then reconnect. See the section headed "Troubleshooting". LED lights up con- Manual control by hand wheel activated. tinuously LED does not light Automatic control with CUT ASSIST activated. Pressing the button activates manual mode. - Page 13 Connect a 110 V drilling feed unit only to a 110 V diamond core drilling machine. Connect the drilling feed unit only to a diamond core drilling machine recommended by Hilti. 1. Check that the carriage is suitable for installation of a drilling feed unit.
-
Page 14: Operation
Making the electrical connection 1. Remove the protective caps from the socket and the connecting cable. Fit the protective caps into each other in order to keep them clean. 2. Plug the connecting cable into the socket. Ensuring supply of cooling water The drilling feed unit and the diamond core drilling machine are water-cooled tools. - Page 15 6.2.3 Depth gage When drilling a blind hole (not all the way through), the drilling feed unit stops the advance movement as soon as the carriage contacts the depth gauge. 6.2.4 Automatic break-through detection When through holes are drilled without use of a depth gauge, the core bit feed movement continues until the core bit projects approx.
- Page 16 Breaks between work and storage at low temperatures At temperatures below 4 °C (39 °F), the water in the cooling circuit has to be blown out with compressed air when drilling is interrupted for more than one hour and before the equipment is stowed away. In order for the water circuit to be drained, the diamond core drilling machine has to be connected to the electricity supply and to the drilling feed unit.
-
Page 17: Troubleshooting
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.hilti.group. - Page 18 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
-
Page 19: Manufacturer's Warranty
▶ Do not dispose of power tools, electronic equipment or batteries as household waste! Manufacturer’s warranty ▶ Please contact your local Hilti representative if you have questions about the warranty conditions. English Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03... - Page 20 English Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 21 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 22 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 23 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...
- Page 24 Hilti = registered trademark of Hilti Corp., Schaan 20190517 Printed: 22.05.2019 | Doc-Nr: PUB / 5236039 / 000 / 03...