Download Print this page
YOKOGAWA STARDOM FCN Technical Information
YOKOGAWA STARDOM FCN Technical Information

YOKOGAWA STARDOM FCN Technical Information

Marine standards

Advertisement

Quick Links

Technical
Information
TI 34P02Q93-01E
STARDOM
FCN Installation Guide
(Marine Standards)
Yokogawa Electric Corporation
2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 Japan
Tel.: 81-422-52-5616 URL: http://www.stardom.biz
TI 34P02Q93-01E
©Copyright Oct. 2018 (YK)
2nd Edition Feb. 25, 2019 (YK)

Advertisement

loading
Need help?

Need help?

Do you have a question about the STARDOM FCN and is the answer not in the manual?

Questions and answers

Summary of Contents for YOKOGAWA STARDOM FCN

  • Page 1 Technical STARDOM FCN Installation Guide Information (Marine Standards) TI 34P02Q93-01E Yokogawa Electric Corporation TI 34P02Q93-01E 2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 Japan ©Copyright Oct. 2018 (YK) Tel.: 81-422-52-5616 URL: http://www.stardom.biz 2nd Edition Feb. 25, 2019 (YK)
  • Page 2 Blank Page...
  • Page 3: Introduction

    For general installation of the FCN-500, refer to “FCN/FCJ Installation Guide (TI 34P 02Q91- 01E)”. IMPORTANT Notation in this document: • The term “FCN-500” refers to the autonomous controllers with NFCP501/NFCP502 CPU module. Only the FCN-500 with NFCP502 is applicable to the marine standards. All Rights Reserved Copyright © 2018, Yokogawa Electric Corporation TI 34P02Q93-01E Oct. 1, 2018-00...
  • Page 4: Safety Precautions

    Safety Precautions Symbol Marks Throughout this Technical Information, you will find several different types of symbols are used to identify different sections of text. This section describes these icons. WARNING Indicates precautions to avoid a danger that may lead to death or severe injury. CAUTION Indicates precautions to avoid a danger that may lead to minor or moderate injury or property damage.
  • Page 5: Copyright And Trademark Notices

    Copyright and Trademark Notices Trademark Acknowledgments • STARDOM and FAST/TOOLS are trademarks of YOKOGAWA. • All other company and product names mentioned in this manual are trademarks or registered trademarks of their respective companies. • We do not use TM or ® mark to indicate those trademarks or registered trademarks in this manual. TI 34P02Q93-01E Oct. 1, 2018-00...
  • Page 6 Blank Page...
  • Page 7: Table Of Contents

    Toc-1 STARDOM FCN Installation Guide (Marine Standards) TI 34P02Q93-01E 2nd Edition CONTENTS Introduction ......................i Safety Precautions ....................ii Copyright and Trademark Notices ...............iii Compliance with Marine Standards ............1-1 Revision Information ....................i TI 34P02Q93-01E Feb. 25, 2019-00...
  • Page 8 Blank Page...
  • Page 9: Compliance With Marine Standards

    1. Compliance with Marine Standards Compliance with Marine Standards The STARDOM FCN-500 Autonomous Controller offers compliance with the following marine standards: • Bureau Veritas (BV) Rules for the Classification of Steel ships-January 2018 edition, Part C Chapter 3 Section 6 (EC Code: 31) • Lloyd’s Register (Lloyd’s Register) Type Approval System Test Specification Number 1 July 2015 (Environmental categories ENV2) This Document introduces the components of systems which comply with the marine standards, and precautions for installing those components.
  • Page 10 1. Compliance with Marine Standards Marine Standard-compliant Components The table below shows the STARDOM components which comply with the marine standards Table Marine Standard-compliant Components Marine Standard Type Model Function Base NFBU200 (*1) Base Module (long)   module NFPW441 Power supply module for FCN (100 - 120 V AC input) ...
  • Page 11 1. Compliance with Marine Standards Precaution on Selecting System Components When building a system, use components which have already obtained type approval for marine standards. For the HMI’s PC and ENG’s PC, use generic computers (including monitors, keyboards, mice, and other peripheral devices) which are accredited by the required marine standards. Precaution on Installing Components Each component shall be installed in accordance with its installation guidance. In addition, all components related with FCN-500 shall be installed in a metal cabinet.
  • Page 12 1. Compliance with Marine Standards Wiring examples of power cables (a) to (d) are shown below according to the mounting position of the noise filter and the tap. Cabinet Cabinet Control unit Control unit Extension unit Extension unit External PSU External PSU AC/DC AC/DC AC/DC AC/DC DC/DC DC/DC DC/DC DC/DC Noise Filter Noise Filter Noise Filter Noise Filter (*2) (*1) (*2) (*1) Power feed Power feed...
  • Page 13 1. Compliance with Marine Standards Installation of Ferrite Cores Attach ferrite cores on the power cables, the communication cables and the signal cables. The following table shows the cables to which ferrite cores are to be attached, the models and quantities of the ferrite cores to be attached, and the locations at which they are to be attached.
  • Page 14 1. Compliance with Marine Standards for HUB FCN-500 Control unit for N2EB100 for N2EB100 FCN-500 Extension unit for N2EB100 Noise Filter Cabinet F010101E.ai Note: IOM is abbreviation of Input/Output Modules. Note: Figures in ( ) show the locations listed in “Table Cables that Need Ferrite Cores to be Attached to, and Ferrite Core Models and Quantities”.
  • Page 15 1. Compliance with Marine Standards for N2EB100 FCN-500 Extension unit Comminication External Field Device Device Power Supply Unit Field Device Terminal Block for Digital I/O External Field Device Field Device Power Supply Unit Terminal Block for Analog I/O Field Device Field Device Noise Noise Filter (*1)
  • Page 16 1. Compliance with Marine Standards Location of Ferrite Cores for Cables For the following cables, be careful about the locations at which you install ferrite cores: Power-line cables: Install ferrite cores on each cable at the nearest possible place to each connector. In order to prevent the load at the connectors, secure the power-line cables to the cabinet frame or dummy plate using cable ties at the nearest possible place to each ferrite core.
  • Page 17 1. Compliance with Marine Standards Installing Unit Components in Cabinet Unit components here indicate the FCN-500 Control units and Extension units. When installing these unit components in a cabinet, dummy plates may have to be installed and a gasket may have to be attached to the dummy plates in the following cases: • There is a large space between unit components.
  • Page 18 1-10 1. Compliance with Marine Standards When Installing Unit Components Unevenly Inside Cabinet When installing unit components unevenly and gathering them to the upper or lower part of a cabinet, leaving a large space in the cabinet, install dummy plates. Attach an EMI shielding gasket to the dummy plates. For the EMI shielding gaskets, use the model introduced in the paragraph under “When Leaving a Large Space between Unit Components.” For how to attach EMI shielding gaskets, refer to “When Leaving a Large Space between Unit Components.”...
  • Page 19: Revision Information

    Revision Information  Title : STARDOM FCN Installation Guide (Marine Standards)  Manual No. : TI 34P02Q93-01E Oct. 2018/1st Edition Newly published Feb. 2019/2nd Edition • Revised Fig “Wiring for power cable”. n For Questions and More Information If you have any questions, you can send an E-mail to the following address. E-mail: stardom_info@cs.jp.yokogawa.com Yokogawa Electric Corporation n Written by n Published by Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750, JAPAN Subject to change without notice.
  • Page 20 Blank Page...