Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dyconn WA502S
Summary of Contents for Dyconn WA502S
- Page 2 Although we try our best, Dyconn makes no claim that the information comprised herein covers all conditions or details in connection with installation or use of this product. Dyconn assumes no responsibility for accuracy or adequacy of information comprised in this document.
-
Page 3: Specifications
l Do not exceed the maximum weight capacity for this product. Exceeding the weight capacity can result in serious personal injury or damage to equipment! Specifications Weight Capacity 50(LBS) / 22.7(KG) Suits LCD Flat Panel Displays 13”(330mm)-30”(762mm) Maximum Extension 18”(457mm) Depth from Wall 3.2”(81.5mm) Tilt adjustment... -
Page 4: Supplied Parts
Supplied Parts Page... -
Page 5: Required Tools
Required Tools ASSEMBLY and INSTALLATION INSPECT THE MOUNT BEFORE ASSEMBLY 1. Carefully inspect/verify that all components are present. 2. If the mount/components are damaged or missing, please contact the company/seller of the product you purchased and report the issue. Note: Read all assembly instructions before staring the installation process. - Page 6 Step 【1】 Wood Wall Installation Drilling into electrical wires or cables can cause serious personal injury! Always make certain that area behind mounting area is free of electrical wires and cables before drilling or installing. Improper installation can lead to mount falling causing severe personal injury or damage to equipment.
- Page 7 Figure 1-2 Figure 1-2 Figure 1-3 4. Insert Philips Screw ST6.3x65mm (3) through Washer (14), Wall Plate (2) and finally into pilot hole. Repeat for remaining Philips Screws. Tighten Philips Screw securely. (See Figure 1-4) Figure 1-4 Page...
- Page 8 Step 【1】 Masonry Wall Installation Drilling into electrical wires or cables can cause serious personal injury! Always make certain that area behind mounting area is free of electrical wires and cables before drilling or installing. Improper installation can lead to mount falling causing severe personal injury or damage to equipment.
- Page 9 Figure 1-6 Figure 1-7 4. Insert Anchor (13) into anchor hole and seat with gentle tapping from hammer. Anchor (13) should be fully engaged into concrete wall. Tighten anchor screw until anchor has fully collapsed against back side of concrete wall. (See Figure 1-8) Figure 1-8 Page...
- Page 10 5. Insert Philips Screw ST6.3x65mm (3) through Washer (14), Wall Plate (2) and finally into pilot hole. Repeat for remaining Philips Screws. Tighten Philips Screws securely. (See Figure 1-9) Figure 1-9 Page...
-
Page 11: Display Installation
Step 【2】 Display Installation Using improper screws or screw size may damage your display. If spacers are required, be sure to use correct size of screws. Proper screws will easily and completely thread into the display mounting holes. Inadequate thread engagement in the display may cause display to fall. - Page 12 3. Determine depth of recessed mounting holes relative to back of surface of display. 4. Select proper length of Screws (6、 8) place the Spacers (4) on the back of display, follow by position and orient the mounting holes in the Tilter Mount Bracket so that the mounting holes on the Tilter Mount Bracket and Spacers (4) are aligned.
- Page 13 Step 【3】 Attaching Wall Mount LCD Arm Assembly Wall Mount LCD Arm will only work when a display is properly installed. Attaching the LCD Arm Assembly 1. Attach the Wall Mount LCD Arm Assembly (1) to Wall Plate (2) by inserting the LCD Arm Assembly downward, into the top of the Wall Plate pole.
- Page 14 3. Place the Cover (11) and tighten with Phillips Screw M6x12mm (12) through Plastic Washer (15) using a Phillip Screwdriver. Do not over tighten. This is to prevent the LCD Arm Assembly to be lift unnecessary. (See Figure 3-3) Figure 3-3 Page...
-
Page 15: Cable Management
Step 【4】 Cable Management Ensure the Wall Mount LCD Arm Assembly is fully extended before connecting cables. Exercise caution when attaching or removing the display to avoid personal injury or damage to equipment. Disconnect power before removing the display. Note: Ensure enough slack in the cables to allow for movement of the Arms. - Page 16 Step 【5】 Adjusting the Display Monitor Forced movement of Mount Bracket without loosening the Screws will damage Wall Mount LCD Arms Assembly or display monitor. Exercise caution when adjusting the display, to support the display to avoid damage to equipment. Disconnect power before removing the display. Adjusting the Wall Mount LCD Arm Assembly Resistance 1.
- Page 17 4. To increase or decrease the resistance of the Pivot Joint to suit display monitor swing side to side, adjust the Tension Hex Cap Screw on front side of the Wall Mount LCD Arm to secure the place. (See Figure 5-3) 5.
- Page 18 6. This product is designed to adjust quickly and easily according to your needs. To adjust the height, remove the Extension Arm from Wall Plate (2) follow by attaching the LCD Arm to achieve your desired position. (See Figure 5-4) 7.
-
Page 19: Ergonomic Guidelines
Step 【6】 Ergonomic Guidelines Note: Proper ergonomic design is necessary to prevent repetitive strain injuries, which can develop over time and can lead to long-term disability 1. Ensure the correct focal distance for ultimate visual comfort. For visual comfort, a viewing distance between 460mm (18”) to 610mm (24”) is recommended. - Page 20 2. To assess the fit between a person and their work, ergonomics recommended that the optimal of your screen position should be slightly below eye level. Viewing angle should be approximately 10°-20° downward of the screen’s center. The lumbar (bottom five vertebrate in the spine) needs to be supported to decrease disc pressure.
- Page 21 Dyconn disclaims any liability for modification, improper installations, or installations over specified weight range. Dyconn will not be liable for any damages arising out of the use or inability to use Dyconn products. Warranty specification is subject to change without prior notice.
Need help?
Do you have a question about the WA502S and is the answer not in the manual?
Questions and answers