S·e (Eala) Related Test Mode; Menu-Related Test Mode; Dual Zone-Related Test Mode; Backup Current Measurement - Kenwood DPX-MP3110 Service Manual

DPX-MP3110/MP3110S
DPX-MP5110U/MP5110US
Procedure Item
Fader
Balance
Bass Level
Middle Level
For item
Treble Level
forwarding
procedure, HPF Front/Rear
press [AUD]
LPF Sub woofer
key and [FM]
Sub Woofer Phase
key briefl y
Volume Offset
Loudness
2ZONE
∗ Continuous forwarding by remote controller is prohibited.
∗ Bass f/Bass Q/Bass EXT/Middle f/Middle Q/Treble f does not appear in the audio adjustment.
■ S·E (eala) related test mode
Procedure
Press [S·E] key briefl y (main unit)
Order of
sequence
S·E (Eala) LV
q
w
e
r
t
∗ Note: For 5 seconds after the establishment of CD source, the switching of S·E is not displayed. (However, the value changes when the key is
pressed.)

■ Menu-related test mode

Press [M.JOG] key briefl y (main unit)
[DNPP/SBF] key, [DIRECT] key (remote control)

■ Dual Zone-related test mode

Press and hold [ATT/■ TI] key in other mode than Standby (main unit)

■ Backup current measurement

Procedure
While ACC OFF (Back Up ON), Reset
16
Procedure
[VOL] knob and
[ ] / [ ] key and
[FM] / [AM] key
[VOL] knob and
[FM] / [AM] key
Run the test with the following order of sequence. (q → w → e → r → t → q → ···)
Setting Value
S·E (Eala) Bass
Off Off
High Off
Low Off
Off High
Off Low
Procedure
Procedure
MUTE terminal is turned OFF after 2 seconds, not after 15 seconds. (During this time, the CD
mechanism does not function.) Turning the terminal OFF in 2 seconds makes the system to be
in low power consumption condition.
TEST MODE
Adjust to 3 steps of R15 ↔ 0 ↔ F15. (Default value: 0)
Adjust to 3 steps of L15 ↔ 0 ↔ R15. (Default value: 0)
Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value: 0)
Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value: 0)
Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value: 0)
Adjust to 2 steps of Through ↔ 180Hz (or 220Hz). (Default value: Through)
Adjust to 2 steps of Through ↔ 60Hz (or 50Hz). (Default value: Through)
Adjust to 2 steps of Reverse ↔ Normal. (Default value: Normal)
Adjust to 2 steps of -8 ↔ 0. (Default value: 0)
Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value: 0) (AUX)
Adjust to 2 steps of OFF ↔ ON. (Default value: OFF)
Adjust to 2 steps of OFF ↔ ON. (Default value: 0)
Display
S·E OFF
LV High
LV Low
Bass High
Bass Low
Continuous forwarding by remote control is prohibited.
To turn ON/OFF Dual Zone. (Default value: OFF)
Description
Note
Change the assigned Track and VOL at the
same time when setting up the S·E
VOL=30
Note
Note
Note