H3C S3610 Series Operation Manual
Rrpp
Hide thumbs
Also See for S3610 Series:
- Operation manual (175 pages) ,
- Quick start manual (84 pages) ,
- Command manual (54 pages)
Table of Contents
Advertisement
Quick Links
Operation Manual - RRPP
H3C S3610&S5510 Series Ethernet Switches
Chapter 1 RRPP Configuration .................................................................................................... 1-1
1.1 RRPP Overview ................................................................................................................. 1-1
1.1.1 Basic Concepts in RRPP ........................................................................................ 1-1
1.1.2 RRPP Packets......................................................................................................... 1-4
1.1.3 Typical RRPP Networking....................................................................................... 1-5
1.1.4 How RRPP Works ................................................................................................... 1-8
1.1.5 Protocols and Standards......................................................................................... 1-9
1.2 RRPP Configuration Task List ........................................................................................... 1-9
1.3 Configuring Master Node................................................................................................. 1-11
1.3.1 Configuration Procedure ....................................................................................... 1-11
1.3.2 Master Node Configuration Example .................................................................... 1-12
1.4 Configuring Transit Node................................................................................................. 1-12
1.4.1 Configuration Procedure ....................................................................................... 1-12
1.4.2 Transit Node Configuration Example .................................................................... 1-13
1.5 Configuring Edge Node ................................................................................................... 1-14
1.5.1 Configuration Procedure ....................................................................................... 1-14
1.5.2 Edge Node Configuration Example....................................................................... 1-15
1.6 Configuring Assistant Edge Node.................................................................................... 1-15
1.6.1 Configuration Procedure ....................................................................................... 1-15
1.6.2 Assistant Edge Node Configuration Example ....................................................... 1-17
1.7 Displaying and Maintaining RRPP................................................................................... 1-18
1.8 RRPP Typical Configuration Examples ........................................................................... 1-18
1.8.1 Configuring Single Ring Topology......................................................................... 1-18
1.8.2 Configuring Single-Domain Intersecting Ring Topology ....................................... 1-20
1.8.3 Configuring Multi-Domain Intersecting Ring Topology.......................................... 1-23
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Related Manuals for H3C S3610 Series
Summary of Contents for H3C S3610 Series
-
Page 1: Table Of Contents
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Table of Contents Table of Contents Chapter 1 RRPP Configuration ....................1-1 1.1 RRPP Overview ......................... 1-1 1.1.1 Basic Concepts in RRPP ..................1-1 1.1.2 RRPP Packets......................1-4 1.1.3 Typical RRPP Networking..................1-5 1.1.4 How RRPP Works .................... -
Page 2: Chapter 1 Rrpp Configuration
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Chapter 1 RRPP Configuration When configuring RRPP, go to these sections for information you are interested in: RRPP Overview RRPP Configuration Task List Configuring Master Node Configuring Transit Node... - Page 3 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration I. RRPP domain The interconnected devices with the same domain ID and control VLANs constitute an RRPP domain. An RRPP domain contains multiple RRPP rings, in which one ring serves as the primary ring and other rings serve as subrings.
- Page 4 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration primary ring and an assistant-edge node on the subring. This node is used in conjunction with the edge node to detect the integrity of the primary ring and perform loop guard.
-
Page 5: Rrpp Packets
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration VII. Multi-domain intersection common port Of the two ports on a node where rings of different domains intersect, the common port is the one on the primary ring that belongs to different domains at the same time. This port must not be on a subring. -
Page 6: Typical Rrpp Networking
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Type Description The master node initiates Complete-Flush-FDB packets to notify the transit nodes to update their own MAC entries and Complete-Flush-FDB ARP entries, and release from blocking ports temporarily when an RRPP ring transits into health state. - Page 7 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration II. Multi-domain tangent rings Master node Device E Domain 2 Transit node Master node Ring 2 Ring 2 Device B Device F Device A Ring 1 Transit node...
- Page 8 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration IV. Dual homed rings Domain 1 Edge node Device A Device B Device E Ring 2 Master node Master node Ring 1 Master node Transit node Ring 3...
-
Page 9: How Rrpp Works
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration There are two or more domains in a network, and there two different common nodes between any two domains. Figure 1-6 defines three RRPP domains, each containing one and only one RRPP primary ring. -
Page 10: Protocols And Standards
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration are down, the master nodes of Ring 2 and Ring 3 will open their respective secondary ports, and thus a loop among B, C, E and F is generated. As a result, broadcast storm occurs. - Page 11 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Caution: It is recommended to configure the primary ring first and then the subring when you configure an RRPP domain. Moreover, a Ring ID cannot be applied to more than one RRPP ring in one RRPP domain.
-
Page 12: Configuring Master Node
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Note: If you need to transparently transmit RRPP packets on a device without enabling RRPP, you should ensure only the two ports accessing an RRPP ring permits the packets of the control VLAN. -
Page 13: Master Node Configuration Example
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Caution: The control VLAN configured for an RRPP domain must be a new one. Control VLAN configuration is required for configuring an RRPP ring. To use the undo rrpp domain command to remove an RRPP domain, you must ensure the RRPP domain has no RRPP ring. -
Page 14: Transit Node Configuration Example
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration To do… Use the command… Remarks ring ring-id node-mode transit [ primary-port Specify the current device interface-type as the transit node of the interface-number ] ring, and specify the... -
Page 15: Configuring Edge Node
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration [Sysname] rrpp enable 1.5 Configuring Edge Node 1.5.1 Configuration Procedure Follow these steps to configure edge node: To do… Use the command… Remarks Enter system view system-view —... -
Page 16: Edge Node Configuration Example
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Caution: The control VLAN configured for an RRPP domain must be a new one. Control VLAN configuration is required for configuring an RRPP ring. A Ring ID cannot be applied to more than one RRPP ring in an RRPP domain. - Page 17 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration To do… Use the command… Remarks Enter system view system-view — Create an RRPP domain rrpp domain domain-id Required and enter its view Specify a control VLAN for...
-
Page 18: Assistant Edge Node Configuration Example
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Caution: The control VLAN configured for an RRPP domain must be a new one. Control VLAN configuration is required for configuring an RRPP ring. A Ring ID cannot be applied to more than on RRPP ring in an RRPP domain. -
Page 19: Displaying And Maintaining Rrpp
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration 1.7 Displaying and Maintaining RRPP To do… Use the command… Remarks Display brief information display rrpp brief about RRPP configuration Display detailed Available in any display rrpp verbose domain... - Page 20 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Domain 1 Device A Eth1/0/1 Device B Eth1/0/1 Transit node Eth1/0/2 Eth1/0/2 Master node Ring 1 Transit node Transit node Eth1/0/1 Eth1/0/2 Eth1/0/1 Device C Eth1/0/2 Device D Figure 1-7 Single ring networking diagram II.
-
Page 21: Configuring Single-Domain Intersecting Ring Topology
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration [Device B-rrpp-domain1] ring 1 enable [Device B-rrpp-domain1] quit [Device B] rrpp enable Perform the following configuration on Device C: <Device C> system-view [Device C] rrpp domain 1... - Page 22 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration Domain 1 Device A Device B Edge node Eth1/0/1 Eth1/0/1 Eth1/0/3 Master node Eth1/0/2 Eth1/0/2 Master node Eth1/0/1 Ring 2 Ring 1 Eth1/0/2 Device E Eth1/0/2 Eth1/0/1...
- Page 23 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration [Device B-rrpp-domain1] ring 1 node-mode transit primary-port ethernet 1/0/1 secondary-port ethernet 1/0/2 level 0 [Device B-rrpp-domain1] ring 2 node-mode edge common-port ethernet 1/0/2 edge-port ethernet 1/0/3 [Device B-rrpp-domain1] ring 1 enable...
-
Page 24: Configuring Multi-Domain Intersecting Ring Topology
Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration 1.8.3 Configuring Multi-Domain Intersecting Ring Topology I. Networking requirements Device A, Device B, Device C and Device D constitute RRPP domain 1, and Device E, Device F, Device C and Device B constitute RRPP domain 2;... - Page 25 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration II. Configuration considerations First, determine the node roles on the primary ring and subring in each RRPP domain, and then perform the following configuration domain by domain on each device: Create RRPP domains;...
- Page 26 Operation Manual – RRPP H3C S3610&S5510 Series Ethernet Switches Chapter 1 RRPP Configuration [Device C-rrpp-domain1] quit [Device C] rrpp domain 2 [Device C-rrpp-domain2] control-vlan 4092 [Device C-rrpp-domain2] ring 2 node-mode transit primary-port ethernet 1/0/3 secondary-port ethernet 1/0/2 level 0 [Device C-rrpp-domain2] ring 2 enable...