Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Port Mirroring Configuration ..................1-1 1.1 Introduction to Port Mirroring ..................... 1-1 1.1.1 Classification of Port Mirroring ................1-1 1.1.2 Implementing Port Mirroring..................1-2 1.1.3 Other Functions Supported by Port Mirroring ............
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration Chapter 1 Port Mirroring Configuration When configuring port mirroring, go to these sections for information you are interested Introduction to Port Mirroring Configuring Local Port Mirroring...
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration Remote port mirroring implements port mirroring between multiple devices. That is, the source ports and the destination port can be located on different devices in a network.
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration Intermediate devices are used to connect source devices and destination devices. An intermediate device forwards the mirrored packets to the next intermediate device or the destination device. If the source device is directly connected to the destination device, no intermediate device is needed.
Page 5
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration To do… Use the command… Remarks mirroring-group group-id You can add ports to In system a port mirroring group mirroring-port view mirroring-port-list { both |...
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration 1.3 Configuring Remote Port Mirroring 1.3.1 Configuring a Remote Source Mirroring Group Follow these steps to configure a remote port mirroring group To do… Use the command…...
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration Note: All the ports of a remote source mirroring group belong to a single device. A remote source mirroring group can contain only one reflector mirroring port.
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration To do… Use the command… Remarks You can add a In system mirroring-group group-id port to a view monitor-port monitor-port-id remote port Add a port...
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration 1.5 Port Mirroring Configuration Examples 1.5.1 Local Port Mirroring Configuration Example I. Network requirements The departments of a company connect to each other through Ethernet switches: Research and Development (R&D) department is connected to Switch C through...
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration [SwitchC] mirroring-group 1 mirroring-port Ethernet 1/0/1 Ethernet 1/0/2 both [SwitchC] mirroring-group 1 monitor-port Ethernet 1/0/3 # Display the configuration of all the port mirroring groups.
Page 11
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration II. Network diagram Switch A Switch B Switch C Reflector Eth1/0/3 port Eth1/0/1 Eth1/0/4 Eth1/0/1 Eth1/0/2 Eth1/0/2 Eth1/0/1 Eth1/0/2 Department 1 Department 2 Data monitoring...
Page 12
Operation Manual – Port Mirroring H3C S3610&S5510 Series Ethernet Switches Chapter 1 Port Mirroring Configuration [SwitchB] interface Ethernet 1/0/1 [SwitchB-Ethernet1/0/1] port link-type trunk [SwitchB-Ethernet1/0/1] port trunk permit vlan 2 [SwitchB-Ethernet1/0/1] quit # Configure port Ethernet 1/0/2 as a trunk port and configure the port to permit the packets of VLAN 2.
Need help?
Do you have a question about the S3610 Series and is the answer not in the manual?
Questions and answers