UEi DMG100 Instruction Manual
  1. Manuals
  2. Brands
  3. UEi Manuals
  4. Measuring Instruments
  5. DMG100
  6. Instruction manual

UEi DMG100 Instruction Manual

Digital micron gauge
Hide thumbs
Table of Contents

Advertisement

Quick Links

be free from
trument should
e repaired or
use and does not
ch results from
t or improper
lting for failed
plied warranties
are limited to
of use of the
s, expenses, or
age, expenses or
iginal purchase
ce charge.
UEi or visit us
o:
7008
6322
ts.
ate to state.
6 4 3 . 6 3 2 2
0 4 . 2 7 8 . 8 2 9 9
COPYRIGHT ♥ 2011
UEi
1.800.561.8187
www.
.com
DMG100
Digital
Micron
Gauge
information@itm.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DMG100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UEi DMG100

Summary of Contents for UEi DMG100

  • Page 1 UEi or visit us 7008 6322 ate to state. 6 4 3 . 6 3 2 2 0 4 . 2 7 8 . 8 2 9 9 COPYRIGHT ♥...

  • Page 2: Parts Diagram

    Parts Diagram ng procedure: ease and then uminate, and f again and repeat. DMG100 is now reset to the . Please use the table Solution ean the Vacuum Sensor the BluVac off, warm the uum port with your hand, turn the BluVac back on.

  • Page 3: Lcd Display

    Place the DMG100 undi Millibar Units Indicator no greater than 30°C (86 Millitorr Units Indicator 10. Allow the DMG100 to wa Millimeters of Mercury Units Indicator will show on the display. 11. Press any key to silence Micron Units Indicator...

  • Page 4: Quick Start

    . (DO NOT INSERT ANY AGE THE SENSOR). Battery Installation & Replacement Remove the battery cover from the rear of the DMG100 by compressing tab at the base of the battery cover. n the sensor to dry it more If necessary, remove and detach old battery from battery clip.

  • Page 5: Battery Level Indicator

    Mode by pressing any key on the keypad. While in Sleep, the gauge will beep twice every 5 minutes to remind you that it is on. The DMG100 will not sleep in the Calibration Mode (see the Calibration section on pg. 8).
  • Page 6 “Analog” Vacuum Level Bar Graph show The DMG100 also displays a Vacuum Level Bar Graph allowing for a quick visual determination of pressure and exit Sleep the vacuum level achieved. Each bar corresponds to a vacuum pressure range depending on units...

  • Page 7: Maintenance

    Sound The DMG100 has an internal speaker that will emit a beep for each valid key press, and also functions as an alarm in the Calibration mode (see the Calibration section on pg. 8). It will also beep Item every 5 minutes in Sleep Mode.

  • Page 8: Calibration Test

    Place the bagged DMG100 into a freezer with a temperature of less than –5°C (23°F). meric Display (during Allow the DMG100 to cool to below -2°C (28.4°F). At this point, the alarm will sound and the (during calibration) display will change to Remove from freezer and press any key to silence the alarm.

  • Page 9: Restoring Factory Calibration

    Main Numeric Display. If not, turn the power off again and repeat. Press five times followed by The gauge will beep 5 times and return to normal operation. The DMG100 is now reset to the original factory calibration. Troubleshooting Under certain conditions, the display may read .

Table of Contents