Related Manuals for quiko BOXTER QK-B24
Summary of Contents for quiko BOXTER QK-B24
- Page 1 USER MANUAL GEARMOTOR FOR GARAGE DOORS BOXTER WARNING!! Before installing, thoroughly read this manual that is an integral part of the pack V03/2016...
-
Page 2: Table Of Contents
PACKING CONTENTS ..................TECHNICAL DATA....................DIMENSIONS ....................... VIEW OF TYPICAL AUTOMATION AND NAMES OF COMPONENTS ....CONSIDERATIONS FOR INSTALLATION............4-5-6-7 INSTALLATION..................... TROUBLESHOOTING................... SAFETY PRECAUTIONS ..................PACKING CONTENTS 1- MOTOR WITH CARTER AND COURTESY LIGHT 1- PACK OF ACCESSORIES 1- CAPACITOR OPTIONAL 1- CONTROL BOARD WITH RECEIVER TECHNICAL DATA... -
Page 3: Dimensions
DIMENSIONS VIEW OF TYPICAL AUTOMATION AND NAMES OF COMPONENTS FIXING PLATE OF THE MOTOR MOTOR ARMS KIT SAFETY EDGE PHOTOCELLS FLASHING LIGHT + ANTENNA CONTROL BOARD (IF NOT INCLUDED IN THE MOTOR) CONSIDERATIONS FOR INSTALLATION Ÿ The installation and testing operations must be performed only by qualified personnel in order to ensure the proper and safe operation of the automated door. -
Page 4: Installation
INSTALLATION Place and securely fix the anchor plate of the telescopic arm to the door frame so that the movement of the arm does not overlap with the existing arm of the door. Make sure there are at least 20 mm of space between the door frame and the box of the counterweights. - Page 5 Place and securely fix the tube support to the door frame, at a distance between 50 and 100 mm downwards by taking as reference the attachment pin of the existing arm.. Tube Tube support support Straight telescopic arms Curved telescopic arms Place the motor M on the fixing plate so that the pinions are in line with the tubes and lock it.
- Page 6 EXAMPLE AUTOMATION TWO MOTORS WITH LATERAL INSTALLATION INSTALLATION OF THE LATERAL FIXING PLATES Place the fixing plates L motor support to the door as illustrated. Place and fix the motors on the fixing plates so that they are in line with the broaching arms at a distance between 50 and 100 mm downwards by taking as reference the attachment pin of the existing arm (fig 2).
- Page 7 EXAMPLE AUTOMATION WITH NON-PROJECTING DOOR Place and securely fix the tube support to the door frame, at a distance of 110 mm under the center of the door (look at fig. 7-8) The rotation axis of the motor must be 110mm under the center of the door Door...
-
Page 8: Troubleshooting
TROUBLESHOOTING SOLUTION PROBLEM PROBABLE CAUSE 230 volt mains voltage Check master switch absent Check for any STOP selectors or commands. Emergency STOP present If not used, check jumper On giving a command with on STOP contact input on the remote the control board control or with the key-switch, the door... - Page 9 DECLARATION OF CONFORMITY (OF THE MANUFACTURER) Manufacturer: QUIKO ITALY SAS Via Seccalegno, 19 36040 Sossano (VI) Italia hereby declares, under his liability, that the products: QK-B24 , QK-B220 are in compliance with the essential safety requirements of the regulations: Electromagnetic Compatibility Directive ......2004/108/EC Low Voltage Directive ............2006/95/EC...
- Page 10 DECLARATION OF CONFORMITY (OF THE INSTALLER) The undersigned: in charge of the set-up, declares that the product: Gate type: are in compliance with the essential safety requirements of the regulations: Electro magnetic Compatibility Directive ......2004/108/EC Low Voltage Directive ............2006/95/EC Machinery Directive ..............2006/42/EC and also declares that the related and/or specific national technical regulations have been followed: EN 12453/EN 12445 on Industrial, Commercial and Residential Gates and Doors –...
- Page 12 21 22...
- Page 16 Quiko Italy Via Seccalegno, 19 36040 Sossano (VI) - Italy Tel. +39 0444 785513 Fax +39 0444 782371 info@quiko.biz www.quikoitaly.com...