Advertisement
TABLE OF CONTENTS, CONT'D
. . . . . . . . . . . . . . . . . . . .
4.7.2.2
Remote
4-7
4.7.2.3
Local Lockout
4-9
4.7.4
Clear
. . . . . . . . . . . . . . . . . . . . . . . .
4-9
. . . . . . . . . . . . . . . .
4.7.3
Terminating Characters
-
The TN, Command
. . . . . . .
4-9
4.7.5
The "W2" Data String
. . . . . . . . . . . . . . . . .
4-11
4.7.6
The "WI" Data String
. . . . . . . . . . . . . . . . .
4-11
4.8
S E C T I O N OF QUANTITIES FOR THE CONTROL AND
SAMPLE DISPLAYS
-
UNITS. SENSORS. RESOLUTIONS AND DEVIATION (Table 4-7)
. . .
4-11
4.8.1
The FOC1 Command
. . . . . . . . . . . . . .
4-11
4.8.2
Units for Sample Display
-
The FlC1 Command
. . . . .
4-11
4.8.3
Control Sensor Selection
-
The F2CC1N1 Command
. . . .
4-11
4.8.4
Sample Sensor Selection
-
The F2SC1N1 Command
. . . .
4-11
4.8.5
Resolution for The Control and Sample
-
The F3CN1 and F3SN1 Commands
. . . . . . . .
4-11
4.8.6
Selection of Deviation for Control and Sample
-
The F4CON, F4COFF, F4SON and F4SOFF Commands
. . . . .
4-12
4.8.7
Selection of
MATH
Functions ON. OFF and CLEAR
-
The F50N, F5OFF and F5CLR Commands
. . . . . . . . . .
4-12
4.8.8
4-12
4.8.9
The A and B ID Information
-
4.8.10 The "WD" Data String
. . . . . . . . . . . . . . . . .
4-12
4.9.1
The Set Point Value
-
The S Command
. . . . . . . . .
4-12
4.9.2
The "WP" Request Data String
. . . . . . . . . . . . .
4-16
4.9.4
Setting the RESET (Integral)
-
The
I
Command
. . . . .
4-16
4.9.5
Setting the
RATE
(Derivative)
-
The D Command
. . . .
4-16
4.9.6
Heater Range
-
The R Command
. . . . . . . . . . . . .
4-16
4.9.7
%
Manual Heater Power
-
The
H
Command
. . . . . . . .
4-16
4.9.8
The "W3" Data String
. . . . . . . . . . . . . . . . .
4-16
4.10.1 SCAN Programming Instructions
. . . . . . . . . . . . .
4-16
4.10.2 Setting the Dwell Time
-
The YAN1N2N3 and YBON2N3 Commands
. . . . . . . . . .
4-16
4.10.3 Enabling the Scan Function
-
The YS Command
. . . . .
4-17
4.10.4 Holding the Scan Function
-
The
YH
Command
. . . . . .
4-18
4.10.5 The
W Y "
Data String
. . . . . . . . . . . . . . . . .
4-18
Units for Control Display and Set Point
-
Sensor Curve
#
Selection
-
The NC1N1N2N3 Command
. . .
The AC1C2 and BC1C2 Commands
. . . . . . . .
4-12
4.9
THE
CONTROL COMMANDS
. . . . . . . . . . . . . . . . . . . .
4-12
4.9.3
Setting the GAIN (Proportional)
-
The P Command
. . .
4-16
4.10 THE
SCANNER
INPUT CARD
. . . . . . . . . . . . . . . . . . .
4-16
4.11
THE
SERVICE REQUEST. STATUS REGISTER. STATUS REPORTS
AND
THE
STATUS REGISTER
MASK
. . . . . . . . . . . . . . . .
4-18
4.11.1 The Service Request
. . . . . . . . . . . . . . . . .
4-19
4.11.2 The Status Register and Status Reports
. . . . . . . .
4-19
4.11.2.1
Status Reports
0
and 1
-
Display and Control Data Ready
. . . . . . .
4-19
4.11.2.2
Status Report 2
-
The Control Channel Limit
.
4-19
iv
COPYRIGHT 3/88 LSCI
Advertisement
