Philips 170X7FB/00 Service Manual page 4

4
190X7&170X7 LCD
Go to cover page
1. General
1.1 Product description
170X7 is the 7th generation of Hudson 17" TFT Flat Panel
Display Monitor. The monitor featured with both DVI-D and
analog signal input interface, and modularized as a display unit
with embedded universal AC power supplies inside monitor
main body. The power button and display control buttons (tact
switch type) are on the front and the right-hand side of the
monitor. The monitor shall support an internal scaler to
automatically enable the monitor to display lower resolution
video modes into 1280 x 1024 full screen display. The image
can be adjusted through OSD control board. These
adjustments can be stored on a board memory including 40
pre-set modes and 19 factory pre-set modes.
1.2. Basic data
1.2.1 LCD panel
Type NR.
Outside dimensions
(D)
Pixel Pitch (mm)
Color pixel arrangement
Display surface treatment : Hard coating (3H), Anti-Glare
Color depth
Backlight
Active area (mm)
View angle at 10:1 CR
Contrast ratio
White luminance (nit)
Gate IC
Source IC
Response time (ms)
1.2.2. Power supply
Main Voltage: AC 90 - 135 Vrms and 170-- 264 Vrms, 50/60±2
Hz
Power cord length: 1.8M
Power cord type: 3 lead with earth plug
Auto power saving: EPA, Nutek, VESA, DPMS,
STATUS H-sync V-sync
On On On
On On On
Sleep mode Off Off
DC Power off
Note :
To achieve under 1 Watt power saving in Sleep Mode:
"Stand-Alone Audio" feature is selected 'OFF'
Volume has to be adjusted to 0% prior to measurement.
1.2.3. Horizontal scan: 30 - 83 KHz
1.2.4. Vertical scan: 56 - 76 Hz
1.2.5. Input signals
The input signals can be applied in two different modes:
1). VESA Analog
The video input consists of red, green, and blue signals. The video
signals are analog
levels, where 0V corresponds to black and 700mV is the maximum
signal amplitude. Input impedance of video pins is 75 ohm +/- 1%.
The capability of sync signal inputs shall include separate sync, composite
sync and sync on green. input impedance: 2k2ohms The signals are
defined as follow:
Separate sync
Technical Data(For 170X7)
: LM170E03-TLB1 (LPL)
(mm) : 358.5 (W) x 296.5 (H) x 17.5
: 0.264 (H) x 0.264 (V)
: 1280 (H) x 1024 (V), RGB stripe
: 16.7 M (6 bit + FRC)
: CCFL, 4 tables, edge-light
: 337.920 (W) x 270.336 (H)
: 80 (R) / 80 (L), 75(U) / 85 (D)
: 800 (typ.)
: 300 (typ. Center 1 point)
: Novatek (TLB1), OKI (TLB2)
: TSB (TLB1), OKI (TLB2)
: 5 (typ.)
Video Power LED
Active <46W Green /With Audio
Active <36W Green / Without Audio
Blanked <1W Amber LED
N / A <1W LED Off
TTL level, Positive/Negative
composite sync
Sync on green H-sync
2). Intel DVI Digital
Input signal: Four channel TMDS signals
Signal source: pattern generator format as attachment
(Table 1 to 40)
1.2.6 Audio
L/R Output power: 2Wrms into 16 Ohm speaker
L/R input via 1.8m hard-wired cable with lime green 3.5mm
plug
Headphone connection will mute speakers.
1.2.7 Input connectors
Input analog D-sub connector pin assignment
PIN No. SIGNAL
1 Red video input
2 Green video input / sync on green
3 Blue video input
4 GND
5 GND --Cable detect
6 Red video GND
7 Green video GND
8 Blue video GND
9 DDC +3.3V or +5V
10 Logic GND
11 GND
12 Serial data line (SDA)
13 H-sync / H+V
14 V-sync
15 Data clock line (SCL)
(2) Input DVI-D connector pin assignment
Pin No. Description
1 T.M.D.S. data2-
2 T.M.D.S. data2+
3 T.M.D.S. data2 shield
4 No Connect
5 No Connect
6 DDC clock
7 DDC data
8 No Connect
9 T.M.D.S. data1-
10 T.M.D.S. data1+
11 T.M.D.S. data1 shield
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)-- Cable detect
16 Hot plug detect
17 T.M.D.S. data0-
18 T.M.D.S. data0+
19 T.M.D.S. data0 shield
20 No Connect
21 No Connect
22 T.M.D.S clock shield
23 T.M.D.S. clock+
24 T.M.D.S. clock-
Sync polarity:
H-sync positive/negative
V-sync positive/negative
TTL level, Positive/Negative
TTL level, Positive/Negative