Electrical Instructions - Philips 170X7FB/00 Service Manual

1. General points
1.1 During the test and measuring, supply a distortion free AC
mains voltage to the apparatus via an isolated transformer
with low internal resistance.
1.2 All measurements mentioned hereafter are carried out at a
normal mains voltage (90 - 132 VAC for USA version, 195 -
264 VAC for EUROPEAN version, or 90 - 264 VAC for the
model with full range power supply, unless otherwise
stated.)
1.3 All voltages are to be measured or applied with respect to
ground, unless otherwise stated.
Note: don't use heat-sink as ground.
1.4 The test has to be done on a complete set including LCD
panel after 30 minutes warm-up at least in a room with
temperature of 25 +/- 5 degree C.
1.5 All values mentioned in these test instruction are only
applicable of a well
aligned apparatus, with correct signal.
1.6 The letters symbols (B) and (S) placed behind the test
instruction denotes
(B): carried out 100% inspection at assembly line
(S): carried out test by sampling
1.7 The white balance (color temperature) has to be tested in
subdued lighted room.
1.8 Repetitive power on / off cycle are allowed except it should be
avoided within 6 sec.
2. Input signal
2.1 Signal type
2.1.1 Video signal input
Signal source: pattern generator format as attachment.
(Table 1 to 39) Reference generator: QuantumData
802G
The input signals can be applied in two different
modes:
1). VESA Analog
The video input consists of red, green, and blue
signals. The video signals
are analog levels, where 0V corresponds to black
and 700mV is the maximum
signal amplitude. Input impedance of video pins is
75 ohm +/- 1%.
2). Intel DVI Digital
Input signal: Four channel TMDS signals
2.1.2 Sync signal input
The capability of sync signal inputs shall include
separate sync, composite sync and
sync on green. input impedance: 2k2 ohms
Thesignalare defined as follow:
Separate sync
Composite sync
Sync on green H-sync
Signal source: pattern generator format as attachment
(Table 1 to 39)
Reference generator: QuantumData 802G
2.2 Input signal mode
Pre-set 39 modes
PRESET VIDEO RESOLUTION
# Resolution H-Frequency Pixel rate V-Frequency
1 640X350 31.5K
2 720X400 31.5K
3 640X480 31.5K
4 640X480 35.0K
Electrical instructions(190X7)
TTL level, Positive/Negative
TTL level, Positive/Negative
TTL level, Positive/Negative
Comment
25.175 70Hz IBM VGA 10h
28.322 70Hz IBM VGA 3h
25.175 60Hz
30.24 67Hz
5 640X480 37.9K
6 640X480 37.5K
7 640X480 43.3K
8 800X600 35.2K
9 800X600 37.9K
10 800X600 48.1K
11 800X600 46.9K
12 800X600 53.7K
13 832X624 49.7K/
14 1024X768 48.4K
15 1024X768 56.5K
16 1024X768 60.0K
17 1024X768 61.1K
18 1024X768 68.7K
19 1152X864 54.0K
20 1152X864 63.9K
21 1152X864 67.5K
22 1152X870 68.7K
23 1152X900 61.8K
24 1152X900 71.8K
25 1280X960 60.0K
26 1280X960 75.0K
27 1280X1024 64.0K
28 1280X1024 71.7K
29 1280X1024 76.0K
30 1280X1024 80.0K
31 1280X1024 81.1K
32 960X720 44.8K
33 960X720 56.4K
34 1280X720 44.8K
35 1280X720 52.5K
36 1280X720 56.5K
37 1280X768 47.8K
38 1280X768 56K
39 1280X768 60.3K
Remark1: The 19 timing modes in
Factory Preset modes
which need to be ensured perfect performance.
Remark2: Other modes can pass with fair performance.
Remark3: If 1280x720 and 960x720 can not be distinguished then
1280x720 is preferred.
Remark4: If 1280x768 and 1024x768 can not be distinguished
.
then 1024x768 is preferred
190X7&170X7 LCD
Go to cover page
31.5 72Hz
31.501 75Hz
36 85Hz
36 56Hz
40 60Hz
50 72Hz
49.498 75Hz
56.251 85Hz
57.28 75Hz MAC
65 60Hz
75 70Hz
78.75 75Hz
83.096 76Hz IBM XGA-2
94.5 85Hz
79.9 60Hz Non-VESA
94.5 70Hz Non-VESA
108 75Hz
100 75Hz MAC
92.94 66Hz SUN Mode
IV
108 76Hz SUN Mode
II
108 60Hz
129.895 75Hz Non-VESA
108 60Hz
117 67Hz SUN Mode
V
130.223 72Hz DOS/V
135 75Hz
135.008 76Hz SUN Mode
I
57.58 60Hz
72.42 75Hz
74.5 60Hz
89.04 70Hz
95.75 75Hz
79.5 60Hz
94.976 70Hz
102.25 75Hz
Blue and Bold texts represent
21