Page 1: Table Of Contents
TFT LCD Colour Monitor Family:HUSON7 Service 170X7FB/00 190X7FB/00 170X7FB/93 190X7FB/27 Service 190X7FB/69 190X7FB/75 Service 190X7FB/93 190X7FB/93 Horizontal Frequencies 30-83KHz TABLE OF CONTENTS Description Page Description Page Important Dafety Notice-------------------------------------2 Wiring Diagram/Block Diagram-----------------------45~49 Technical Data/Installation-------------------------------3~6 Scaler Diagram/C.B.A-----------------------------------50~55 Audio Diagram/C.B.A------------------------------------56~63 On-Screen Display/Aging Mode-----------------------7~11 Factory Mode/Pixel defect policy--------------------12~13 Power Diagram/C.B.A-----------------------------------64~66...
Page 2: Important Dafety Notice
PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S Company** Equipment. The service procedures REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR recommended by Philips and described in this service PART NUMBERS IN THE PARTS LIST SECTION OF THIS manual are effective methods of performing service SERVICE MANUAL.
Page 3: Technical Data/Installation
Technical Data(For 190X7) 190X7&170X7 LCD Go to cover page General Composite sync TTL level, Positive/Negative Product description Sync on green H-sync TTL level, Positive/Negative 190X7 is the 7th generation of Hudson 19" TFT Flat Panel Display Monitor. 2). Intel DVI Digital The monitor featured with both DVI-D and analog signal input interface, and Input signal: Four channel TMDS signals modularized as a display unit with embedded universal AC power supplies...
Page 4 Technical Data(For 170X7) 190X7&170X7 LCD Go to cover page General composite sync TTL level, Positive/Negative Sync on green H-sync TTL level, Positive/Negative Product description 2). Intel DVI Digital 170X7 is the 7th generation of Hudson 17" TFT Flat Panel Input signal: Four channel TMDS signals Display Monitor.
Page 5 Connection to PC 190X7&170X7 LCD Go to cover page Rear View Front view Connecting to your PC If you use an Apple Macintosh, you need to connect the special Mac adapter to one end of the monitor signal cable.
Page 6 Connection to PC 190X7&170X7 LCD Connect to PC Turn off your computer and unplug its power cable. Connect the monitor signal cable to the video connector on the back of your computer Plug the power cord of your computer and your monitor into a nearby outlet USB plug Connect USB upstream port on monitor and the USB port on PC with a USB cable.
Page 7: On-Screen Display/Aging Mode
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.
Page 8 On Screen Display 190X7&170X7 LCD Go to cover page Only available for Europe Model...
Page 9 On Screen Display 190X7&170X7 LCD Go to cover page Only available for Nafta Model...
Page 10 On Screen Display 190X7&170X7 LCD Go to cover page Only available for Asia Pacific Model...
Page 11 OSD Lock/Unlock,Aging Mode 190X7&170X7 LCD Go to cover page CANNOT DISPLAY THIS VIDEO MODE.. Front Control Panel This screen warns when the input frequency from the computer is not a standard video mode or out of the monitor's scanning range. Please change the display mode of the operating software in the com- puter(i.e.windows) to 1280*1024@60HZ for best display results.
Page 12 ANG1 : For analog only project control (0:Dual, 1:Analog only) IDX : Limit current of inverter, 170X6: 200, 190X6: 245 SCALER : Read/Write scaler register NVRAM : Read/Write eeprom address Panel : LG (LG.Philips panel) Access Factory Mode How to get into Factory Mode Menu Step1: Turn off monitor.
Page 13: Factory Mode/Pixel Defect Policy
Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or subpixel defects exceeding the tolerances listed in the following tables.
Page 14: Mechanical Instructions
Mechanical Instructions 190X7&170X7 LCD Go to cover page Front View Step 2: Unscrew 3 screws as shown in Fig. 4. Fig. 1 Fig. 4 Back View Step 3: -Unscrew the four screws as shown in Fig. 5. - Remove the base. Fig.
Page 15 Mechanical Instructions 190X7&170X7 LCD 15 Go to cover page Step 7: Unscrew 9 screws as shown in Fig. 11. Disconnect 8 connectors as shown in Fig. 11. =======> Fig. 8 LIPS(DELTA) SCALER ASSY Step 5: Remove the Back Cover Assy -Remove the Control Board from the Back Cover Assy -Unscrew 9 screws as shown in Fig.
Page 16: Display Adjustment/Trouble Shooting
Display Adjustment 190X7&170X7 LCD Go to cover page Alignment procedure 1. Turn on the LCD monitor. Clear image Clear image 2.Turn on the Timing/pattern generator. See Fig.1 Resolution :1280x1024(Use the best resolution) Timing : H= 31.47KHz V=60Hz 3. Preset LCD color Analyzer CA-110 -Remove the lens protective cover of probe CA-A30.
Page 17 Trouble Shooting 190X7&170X7 LCD Go to cover page...
Page 18 Trouble Shooting 190X7&170X7 LCD...
Page 19: Warning Message
Warning message 190X7&170X7 LCD Go to cover page Item Attention Signals Display Time Condition Attention off Can not display this 30 mins This warning appears when the video mode, change input signal from your computer computer display input is not in a standard video mode to 1280x1024@60Hz or is out of the monitor s scanning range.
Page 20 Warning Message 190X7&170X7 LCD Go to cover page OSD MAIN CONTROLS 3 secs This message will appear 3 UNLOCKED seconds to indicate the OSD MAIN CONTROLS status when to un-lock it by pressing " " MENU(OK) button for more than 10 seconds while there is video input from THIS IS 85HZ 10 mins...
Page 21: Electrical Instructions
Electrical instructions(190X7) 190X7&170X7 LCD Go to cover page General points 5 640X480 37.9K 31.5 72Hz During the test and measuring, supply a distortion free AC 6 640X480 37.5K 31.501 75Hz mains voltage to the apparatus via an isolated transformer with low internal resistance. 7 640X480 43.3K 85Hz...
Page 22: Electrical Instructions
Electrical instructions(190X7) 190X7&170X7 LCD Go to cover page Allowed 85 Hz overscan signal mode specified EEPROM presetting (B) Once the signal input of PC is 85Hz, this monitor is able to display at least for After finishing all the adjustment need to reset: 10 minutes.
Page 23 Electrical instructions(170X7) 190X7&170X7 LCD Go to cover page General points 4 640X480 35.0K 30.24 67Hz During the test and measuring, supply a distortion free AC 5 640X480 37.9K 31.5 72Hz mains voltage to the apparatus via an isolated transformer with low internal resistance. 6 640X480 37.5K 31.501...
Page 24 Electrical instructions(170X7) 190X7&170X7 LCD Go to cover page Remark1: The 19 timing modes in Blue and Bold texts represent Factory Adjustment of sRGB Preset modes Apply a 1280*1024 / 60Hz signal with white pattern, set brightness to 100%, and which need to be ensured perfect performance. Remark2: Other modes can pass with fair performance.
Page 25: Samrtlage Lite
Introduction Philips Smartlmage Lite Features with Philips LightFrame Technology to enhance your front of scrennperformance depend by content type.It is changing brightness or contrast profiles to enrich color of image and sharpentest.No matter your application is on test processing or watching image or video,you can always get best viewing experience from Philips Smartlmage Lite.
Page 26: Smartmanage
Go to cover page Introduction Philips SmartManage is an advanced solution for users, corporate/institution IT administrator in particular, to manage their Philips monitors as part of the asset management environment. The solution includes three essential components, Philips SmartManage Administrator, and Philips SmarControl and Agent.
Page 27: Ddc Instructions
DDC Instructions 190X7&170X7 LCD Go to cover page General Pin Assignment The digital only connector contains 24 signal contacts organized in DDC Data Re-programming three rows of eight contacts. Signal pin assignments are listed in the In case the DDC data memory IC or main EEPROM which storage all following table: factory settings were replaced due to a defect, the serial numbers have to be re-programmed"Analog DDC IC, &...
Page 28 DDC Instructions 190X7&170X7 LCD Go to cover page Configuration and procedure 3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID46 (for example, C:\EDID46, as shown in Fig. 6). There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is also called Software DDC.
Page 29 DDC Instructions 190X6&170X6 LCD Go to cover page Re-programming Analog DDC IC Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10. 1=Power connector 2=D-SUB connector Fig. 13 DC Power 8-12V Step 3: Modify DDC data (verify EDID version, week, Monitor Printer year)
Page 30 DDC Instructions 190X6&170X6 LCD Click Next , bring up Fig.16. Click Next , bring up Fig.19. Fig. 19 Fig. 16 Click Next , bring up Fig. 20. Click Next , bring up Fig.17. Fig. 20 Fig. 17 Click Next , bring up Fig. 21. Click Next , bring up Fig.18.
Page 31 DDC Instructions 190X7&170X7 LCD 190X7&170X7 LCD Go to cover page Step 8: Modify serial number in OSD Click Next , bring up Fig. 22. 1. Unzip the serial number.zip to your computer, then open the folder - In this step, please confirm the Descriptor Data Type is as shown in Fig.27.
Page 32 DDC Instructions 190X7&170X7 LCD Go to cover page Re-programming Digital DDC IC Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 31. 1=DVI-D connector 2=D-sub connector 3=Power Plug Select and fill out, If necessary. Fig.
Page 33 DDC Instructions 190X7&170X7 LCD Go to cover page Click Next , bring up Fig. 43. Click Save. - In this step, please confirm the Descriptor Data Type is Monitor Step 7: Exit DDC program Range Limits, and all the items are same as below. - Click Finish to exit the Step window.
Page 34 : TY30636123456 640 x 480 @67Hz (Apple,Mac II) Monitor Descriptor #3 640 x 480 @72Hz (VESA) Monitor Name : Philips 190X 640 x 480 @75Hz (VESA) Monitor Descriptor #4 800 x 600 @56Hz (VESA) Monitor Range Limits 800 x 600 @60Hz (VESA) Min.
Page 35 DDC DATA(190X7) 190X7&170X7 LCD Go to cover page Max. Vt rate Hz : 76 Min. Horiz. rate kHz : 30 Max. Horiz. rate kHz : 83 Max. Supported Pixel : 140 No secondary GTF timing formula supported. Extension Flag Check sum : 77 (HEX.) ********************************************************************** EDID data (128 bytes)
Page 36 : TY30636123456 640 x 480 @67Hz (Apple,Mac II) Monitor Descriptor #3 640 x 480 @72Hz (VESA) Monitor Name : Philips 190X 640 x 480 @75Hz (VESA) Monitor Descriptor #4 800 x 600 @56Hz (VESA) Monitor Range Limits 800 x 600 @60Hz (VESA) Min.
Page 37 DDC DATA(190X7) 190X7&170X7 LCD Go to cover page Extension Flag Check sum : 16 (HEX.) ********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 4c 11: 08 12: 40 13: e2 14: 01 15: 00 16: 24 17: 10 18: 01 19: 03 20: 80 21: 26 22: 1e 23: 78 24: ee 25: cd 26: 65 27: a2 28: 59 29: 4a 30: 9e 31: 24 32: 12 33: 50 34: 54 35: bf 36: ef 37: 80 38: 71 39: 4a...
Page 38 640 x 480 @60Hz (IBM,VGA) Monitor Descriptor #2 640 x 480 @67Hz (Apple,Mac II) Serial Number : TY30636123456 640 x 480 @75Hz (VESA) onitor Descriptor #3 800 x 600 @56Hz (VESA) Monitor Name : Philips 170X 800 x 600 @60Hz (VESA)
Page 39 DDC DATA(170X7) 190X7&170X7 LCD Go to cover page Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz : 56 Max. Vt rate Hz : 76 Min. Horiz. rate kHz : 30 Max. Horiz. rate kHz : 83 Max. Supported Pixel : 140 No secondary GTF timing formula supported.
Page 40 Established Timings Monitor Descriptor #3 Established Timings I : 720 x 400 @70Hz (IBM,VGA) Monitor Name : Philips 170X 640 x 480 @60Hz (IBM,VGA) Monitor Descriptor #4 640 x 480 @67Hz (Apple,Mac II) Monitor Range Limits 640 x 480 @72Hz (VESA) Min.
Page 41 DDC DATA(170X7) 190X7&170X7 LCD Go to cover page ********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 4b 11: 08 12: 40 13: e2 14: 01 15: 00 16: 24 17: 10 18: 01 19: 03 20: 80 21: 22 22: 1b 23: 78 24: ee 25: 2e 26: e5 27: a4 28: 57 29: 4a 30: 9c 31: 25 32: 11 33: 50 34: 54 35: bf 36: ef 37: 80 38: 71 39: 4a...
Page 42: Firmware Upgrade For Cpu
Firmware Upgrade for CPU 190X7&170X7 LCD Go to cover page Go to cover page Configuration and procedure "Easywriter " The software is provided by Novatek to upgrade the firmware of CPU. It is a windows-based program, which cannot be run in MS-DOS. DDC2BI_ISP TOOL (3138 149 53161) is for the interface between "Parallel Port of PC"...
Page 43 Firmware Upgrade for CPU 190X7&170X7 LCD Go to cover page Fig. 10 Fig. 7 Press the file --> exit to end program , as shown in Fig. 11. Press the Load hex then select the hex as shown in Fig. 8. Fig.
Page 44 Firmware Upgrade for CPU 190X7&170X7 LCD Go to cover page Go to cover page 5 Check the firmware version 1). Turn off monitor. [Push "AUTO" & "OK" buttons at the same time and hold them] +[Press "power" button untill comes out "Windows screen" ] =>...
Page 45: Wiring Diagram/Block Diagram
Wiring Diagram(170X7) 190X7&170X7 LCD Go to cover page 1930 1930 CON301 CON301...
Page 46 Wiring Diagram(190X7) 190X7&170X7 LCD Go to cover page Go to cover page...
Page 47 190X7&170X7 LCD Block Diagram(170X7) X Series System Block Diagram X Series System Block Diagram Specification : SXGA Analog : 1280 x 1024 / 75Hz Digital : 1280 x 1024 / 75Hz Backlight Panel Upstream From PC (USB type B) Backlight LVDS Interface USB PLUG Power...
Page 48 Block Diagram(170X7) 190X7&170X7 LCD Go to cover page System/Chassis Architecture System/Chassis Architecture Backlight Panel LVDS Brightness USB PLUG BL_CTRL Panel_ID Power Scaler USB Device Board 11Pin Board Architecture Audio & Control BD & Power/SmartImage Sensor PC-Audio Headphon Control...
Page 49 190X7&170X7 LCD Block Diagram(190X7)
Page 50: Scaler Diagram/C.b
190X7&170X7 LCD Scaler Diagram...
Page 51 190X7&170X7 LCD 190X7&170X7 LCD Scaler Diagram...
Page 52 Scaler Diagram 190X7&170X7 LCD Go to cover page...
Page 53 190X7&170X7 LCD Scaler Diagram...
Page 54 190X7&170X7 LCD 190X7&170X7 LCD Scaler Board C.B.A Go to cover page...
Page 55 190X7&170X7 LCD Scaler Board C.B.A...
Page 56: Audio Diagram/C.b
AUDIO DIAGRAM(170X7) 190X7&170X7 LCD Go to cover page...
Page 57 190X7&170X7 LCD AUDIO DIAGRAM(170X7) U 1 B 2 U 2 C 2 U 3 C 2 U 4 D 2 U 5 E 2 U 6 E 2 U 7 C 6 A U D I O B O A R D U 8 B 2 U 9 B 6 S B : 60535 x12...
Page 58 Audio Board C.B.A(170X7) 190X7&170X7 LCD Go to cover page...
Page 59 190X7&170X7 LCD Audio Board C.B.A(170X7)
Page 60 AUDIO DIAGRAM(190X7) 190X7&170X7 LCD Go to cover page...
Page 61 190X7&170X7 LCD AUDIO DIAGRAM(190X7)
Page 62 Audio Board C.B.A(190X7) 190X7&170X7 LCD Go to cover page...
Page 63 190X7&170X7 LCD Audio Board C.B.A(190X7)
Page 64: Power Diagram/C.b
POWER DIAGRAM 190X7&170X7 LCD Go to cover page...
Page 65 190X7&170X7 LCD POWER DIAGRAM...
Page 66 Power Board C.B.A 190X7&170X7 LCD Go to cover page...
Page 67: Usb Diagram/C.b
USB DIAGRAM 190X7&170X7 LCD...
Page 68 190X7&170X7 LCD USB Board C.B.A Go to cover page...
Page 69 190X7&170X7 LCD USB Board C.B.A...
Page 70: Control&Earphone Diagram/C.b
CONTROL&EARPHONE DIAGRAM 190X7&170X7 LCD Go to cover page...
Page 71 Control Board C.B.A 190X7&170X7 LCD...
Page 72 EARPHONE BOARD C.B.A 190X7&170X7 LCD Go to cover page...
Page 73: Exploded View
EXPLODED VIEW(170X7) 190X7&170X7 LCD 190X7&170X7 LCD 190X7&170X7 LCD...
Page 74: Exploded View
EXPLODED VIEW(190X7) 190X7&170X7 LCD...
Page 75: Recommended Parts List
Recommended Parts List 190X7&170X7 LCD Go to cover page Recommended Parts List Recommended Parts List TYPE:170X7FB/00(CPT) TYPE:190X7FB/00(LPL) Item Philips 12NC Description TPV 18NC Item Philips 12NC Description TPV 18NC 9965 000 42181 BACK COVER ASSY 705GP7K0B34002 9965 000 42374 BACK COVER ASSY...
Page 76 12NC:863900017123 C216 9965 000 42231 CAP CHIP 0603 330P 50V NPO /-5% 065G060333131J C217 9965 000 37790 CER1 0603 NP0 50V 33P PM5 R Item Philips 12NC TPV 18NC 065G060333031 Description C217 9965 000 42230 CAP CHIP 0603 33P 50V NPO /-5%...
Page 77: Spare Parts List
Spare Parts List 190X7&170X7 LCD R305 9965 000 42213 RST CHIPR 100 OHM -5% 1/10W 061G0603101 C504 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R306 9965 000 42213 RST CHIPR 100 OHM -5% 1/10W 061G0603101 C504 9965 000 42228 CAP CHIP 0603 100N 16V X7R /-10 065G060310412K R307 9965 000 42225 RST CHIPR 4.7KOHM -5% 1/10W 061G0603472...
Page 78: Spare Parts List
Q406 9965 000 37397 TRA SIG SM MUN2211J(ONSE)R 057G7601PH 2944 9965 000 36004 0.01UF -10% 50V X7R 065G060310332 Q406 9965 000 42211 TRA PDTC114EK SC-59 PHILIPS 057G7602PH 2944 9965 000 42260 CAP CHIP 0603 10N 50V X7R /-10% 065G060310332K Q505 9965 000 37785 TRA SIG SM BC857CG (ONSE) R...
Page 79 Sparts Parts List 190X7&170X7 LCD 190X7&170X7 LCD 7942 9965 000 37397 TRA SIG SM MUN2211J(ONSE)R 057G7601PH 7942 9965 000 42211 TRA PDTC114EK SC-59 PHILIPS 057G7602PH 7942 9965 000 42252 TRA KRC102S KEC 057G760500KEC 7943 9965 000 37397 TRA SIG SM MUN2211J(ONSE)R...
Page 80 065G060347312K MODEL:190X7FB/00(LPL) 12NC:863900017126 C225 9965 000 42232 CAP CHIP 0603 47N 16V X7R /-10% 065G060347312K Item Philips 12NC Description TPV 18NC C227 9965 000 42232 CAP CHIP 0603 47N 16V X7R /-10% 065G060347312K C228 9965 000 42232 CAP CHIP 0603 47N 16V X7R /-10%...
Page 81 Spare Parts List 190X7&170X7 LCD R315 9965 000 42213 RST CHIPR 100 OHM -5% 1/10W 061G0603101 C507 9965 000 42234 EC 47UF 25V HV 6.3X5.5MM 067G3114704T R316 9965 000 42213 RST CHIPR 100 OHM -5% 1/10W 061G0603101 C507 9965 000 42235 EC 47UF 25V RVS 6.3X5.3MM 067G3134704T R317 9965 000 42213 RST CHIPR 100 OHM -5% 1/10W 061G0603101...
Page 82 190X7&170X7 LCD Go to cover page Q406 9965 000 42211 TRA PDTC114EK SC-59 PHILIPS 057G7602PH 2972 9965 000 42259 CAP CHIP 0603 100P 50V NPO /-5% 065G060310131J Q505 9965 000 42210 TRA BC857CG 100MA/45V SOT-23 057G420901T 2973 9965 000 42259 CAP CHIP 0603 100P 50V NPO /-5%...
Page 83 Spare Parts List 190X7&170X7 LCD PCB Assy 9965 000 42191 CONTROL ASSY Various 1931 9965 000 42278 SWI TACT SM 1P 1POS SKQGAB R 077G6041AL 1931 9965 000 42279 TACT SW BY FORWARD SFKQGMA2125T077G6072FD 1932 9965 000 42278 SWI TACT SM 1P 1POS SKQGAB R 077G6041AL 1932 9965 000 42279 TACT SW BY FORWARD SFKQGMA2125T077G6072FD 1933 9965 000 42278 SWI TACT SM 1P 1POS SKQGAB R...
Page 84: Repair Tips/Repair Flow Chart
Repair Tips 190X7&170X7 LCD 190X7&170X7 LCD Go to cover page 0. Warning preferably be equipped with a thermal control (soldering temperature: 225 to 250 C). All ICs and many other semi-conductors are susceptible to - The chip, once removed, must never be reused. electrostatic discharges (ESD).
Page 85 190X7&170X7 LCD Go to cover page 3. Lead-free product identification You can identify lead-free product by Philips-lead-free logo on PCB. 4. Lead-free product repair instruction 4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 149 00108(1.0mm SAC305).
Page 86 X 21 190X7&170X7 LCD 190X7&170X7 LCD Repair Flow Chart Go to cover page AC IN Power Board Control Board Scaler Board LCD Panel No power (power indicator off) Check 12V/5V/3.3V Bad power board Bad Scaler Board Check Scaler Board Check Control Board Check Control Wires Check LCD Panel...
Page 87 Repair Flow Chart 190X7&170X7 LCD Go to cover page Bad Power Board Power Board Check Scaler Board Bad Scaler Board...
Page 88 X 21 190X7&170X7 LCD Repair Flow Chart Go to cover page Check Scaler Board Check LCD Panel Control Board Board...
Page 89: General Product Specification
. ANTI-GLARE TO REDUCE LIGHT REFLECTION . POWER MANAGEMENT CAPABILITY . SOG SUPPORT . MPR ( TCO 06 Optional ) . SMART CONTROL REQUIREMENT . WEEE REQUIREMENT . RoHS REQUIREMENT . USB PLUG SUPPORT 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 90 PER PHILIPS GRAPHI SHEET THE GAP BETWEEN PANEL AND FRONT BEZEL<0.8MM LOCATION OF CONTROL ICONS PER PHILIPS GRAPHIC SHEET COLOR FOR RESIN/PAINT PER PHILIPS MAKE UP SHEET 24 RESINS IF PAINT IS USED PLASTICS MOLD TOOLING 5.10 PLASTICS FLAMMABILITY 5.11 TESTURE/GLOSSING OF HOUSING 5.12 TILT AND SWIVEL BASE...
Page 91 PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet which has an integrated tilt and foldable base and the chassis is NovaTek platform NT68665. 2.1.1 Type NR.
Page 92 The input signals are applied to the display through DVI-D cable. Length : 1.8 M +/- 50 mm (bundle within packing) Connector type : DVI-D male with DDC2B pin assignments White connector thumb-operated jack screws pin assignment : 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 93 TMDS data1- TMDS data1+ TMDS data1 shield Ground(return for +5V and H/V-sync)(Cable Detect) Hot plug detect TMDS data0- TMDS data0+ TMDS data0 shield TMDS clock shield TMDS clock+ TMDS clock- 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 94 Digital(DVI-D) More Settings Language Phase/ Clock Phase Clock OSD Settings Horizontal Vertical Audio Options Stand-alone Mute Reset Serial No.: (Serial No.) Timing Mode Up/Down to Move, ok to Confirm 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 95 Analog(D-Sub), Digital(DVI-D) More Settings Language Phase/ Clock(Grey out) OSD Settings Horizontal Vertica Audio Options Stand-alone Mute Reset Serial No.: (Serial No.) Timing Mode Up/Down to Move, ok to Confirm 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 96 Because each preset profiles will define default setting of these 3 parameters. User can understand what is the value of that in preset profile by open the main OSD. 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 97 Enhancement Point: Pre-setting contrast enhancement should be implemented. Sharpness and color to be enhanced 90%. Color temperature 6500° or native ( if higher) Brightness level sets to 90. 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 98 3.31.2 3. 3 Timing requirement 3.3.11.2.2Mode storing capacity 3 . 3. 1 Factory preset modes : 19 Preset modes : 40 3. 3. 2 3.3.21.2.3Factory preset timings (19 modes) 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 99 S ( ms ) 1.175(37 lines) 0.381(13 lines) 0.317 ( 10 0.086( 3 line ) line ) SYNC. H/V - / - - / - POLARITY SEP . SYNC 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 100 0.770 ( 37 line ) 0.021 ( 1 line ) 0.018 ( 1 lines) SYNC. H/V + / + + / + + / + + / + POLARITY SEP . SYNC 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 101 S ( ms ) 0.016 ( 1 line ) 0.014 ( 1 line ) 0.074(4 lines) 0.016(1 lines) SYNC. H/V + / + + / + POLARITY SEP . SYNC 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 102 0.017(1 lines) 0.04 ( 3 lines ) 0.015 ( 1 line) 0.028 (2 lines ) SYNC. H/V + / + + / + + / + POLARITY SEP . SYNC 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 103 R ( ms ) 16.081(720 lines) 12.766(720 lines) 16.082 13.714 S ( ms ) 0.0228(1 lines) 0.0184(1 lines) 0.067 0.019 SYNC. H/V -/ + -/ + POLARITY SEP . SYNC 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 104 In accordance with VESA Display Channel Standard Ver.1.0 and having DDC 2B capability in accordance with DVI requirement (DDWG digital Visual Interface revision 1.0) use DDC 2B and EDID ver. 1.3. 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 105 Apply full gray64 pattern, with brightness in 100 % position and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center should be: 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 106 If paint is used · RoHs required · WEEE required · Must meet PHILIPS Standard like UN-D1235 and etc. 5.91.9 Plastic mold tooling 5 .9 · Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines, gate marks, ejector marks, etc.).
Page 107 GENERAL PRODUCT SPECIFICATION Go to cover page 5.111.1 5. 11 Texture/Glossing of housing · The texture area and texture No. should follow Philips make-up sheet. · The exterior surfaces shall have a uniform texture. · Philips must approve the mold texturing. ·...
Page 108 Layer --|15 16|15 --|15 16|15 --|17 18|17 Sets / Layer Sets / Block --|90 96|90 --|90 96|90 --|102 108|102 Blocks/Container --|22 20|2 20|2 Total Sets 1980 2100 2244 2364 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 109 8 . 1 According to MIL-STD-1916 (Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00 Philips' Flat Panel Monitors Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy , 170X7 sPPpanelproduct. BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 170X7 MODEL...
Page 110 TOTAL DOT DEFECTS ACCEPTABLE LEVEL 170X7 MODEL Total bright or black dot defects of all type * 1 or 2 adjacent sub-pixel defects = 1 dot defect Fig 1: Brightness Uniformity 17 Inch LCD Monitor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 111 Go to cover page Cross talk pattern Gray level 46 (64 Gray level) Cross talk Pattern Fig 3: Center at Gray level 0 (Black) 1 7 I n c h LC D Mo n i tor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 112 112 190X7&170X7 LCD GENERAL PRODUCT SPECIFICATION Go to cover page SEPARATE SYNC. VIDEO HORIZONTAL VIDEO VERTICAL COMPOSITE SYNC. VIDEO HORIZONTAL FIG-4 TIMING CHART -1 1 7 Inc h LC D Moni tor TYPE :170X7FB/00 BRAND : PHILIPS 2006-10-15 2006-10-15...
Page 113: Safety Test Requirements
Safety Test Requirements 190X7&170X7 LCD Go to cover page 3. Equipments and Connection All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both Hipot Ground Continuity testing. 3.1. Equipments For example : HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY 1.Application requirements...

This manual is also suitable for:

190x7fb/27 Huson7 series 190x7fb/00 170x7fb/93 190x7fb/75 190x7fb/69 ... Show all

Philips 170X7FB/00 Service Manual

Quick Links

TABLE OF CONTENTS

Related Manuals for Philips 170X7FB/00

Summary of Contents for Philips 170X7FB/00

This manual is also suitable for:

Table of Contents