Roland AX-Edge Parameter Manual page 34

SYSTEM EFFECT Parameters
Reverb Parameters
NOTE
The SYSTEM EFFECT reverb cannot be edited if the currently selected
"PRG"
program's REVERB Src is set to
program sound parameters). You can either edit the reverb settings for the
program, or change Src to "SYS"
INTEGRA
Parameter Value
01: ROOM1
02:
ROOM2
Type 03:
HALL1
04: HALL2
05: PLATE
Pre Delay 0–100 [msec]
Time
0.1–10.0 [sec]
Density 0–127
Diffusion 0–127
LF Damp 0–100
HF Damp 0–100
Spread 0–127
Tone 0–127
WARM HALL
Parameter Value
Pre Delay 0–100 [msec]
Time 0.3–30 [sec]
16–15000 [Hz],
PreLPF
Bypass
16–15000 [Hz],
PreHPF
Bypass
16–15000 [Hz],
PreLoop LPF
Bypass
Diffusion 0–127
HF Damp Freq 1000–8000 [Hz]
HF Damp Ratio 0.1–1.0
HALL
Parameter Value
Pre Delay 0.0–100 [msec]
Time
0–127
Size 1–8
160–12500 [Hz],
High Cut
BYPASS
Density 0–127
Diffusion 0–127
LF Damp F 50–4000 [Hz]
(the settings are specified by the
and edit them.
Explanation
Selects the types of reverb.
OFF:
Reverb is not used
Room 1/2: Room
Hall 1/2: Hall
Plate: Plate
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time length of reverberation
Density of reverb
Adjusts the change in the density of the
reverb over time.
The higher the value, the more the
density increases with time.
(The effect of this setting is most
pronounced with long reverb times.)
Adjusts the low-frequency portion of the
reverb.
Adjusts the high-frequency portion of
the reverb.
Reverb spread
Tonal character of the reverb
Explanation
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time length of reverberation
Frequency above which to cut the high-
frequency portion of the sound entering
the reverb
Frequency below which to cut the low-
frequency portion of the sound entering
the reverb
Frequency above which to cut the
high-frequency portion of the extended
reverberation
Adjusts the change in the density of the
reverb over time.
Frequency above which to cut the high-
frequency portion of the reverb
Amount by which to attenuate the high-
frequency portion of the reverb
Explanation
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time length of reverberation
Size of room/hall
Frequency above which the high-
frequency portion of the final output
sound is cut (BYPASS: no cut)
Density of reverb
Adjusts how reverb density increases over
time. (This effect is especially noticeable
with long reverb times.)
Frequency below which the low-
frequency portion of the reverb sound
is cut.
Parameter Value
LF Damp G
-36–0 [dB]
HF DampF 4000–12500 [Hz]
HF Damp G -36–0 [dB]
GS
Parameter Value
ROOM1–3,
Char
HALL1–2, PLATE,
DELAY, PAN-DELAY
Pre LPF 0–7
Level 0–127
Feedback
0–127
SRV2000
Parameter Value
Selects the type of reverb offered by the Roland SRV-2000
digital reverb.
R37–R0.3
Selection
H37–H15
P-B
P-A
Pre Delay 0–160
Time 1–990 [msec]
HF Damp
0.05–1.00
Density 0–9
Attack Gain 0–9
Attack Time 0–9
ER Density 0–9
ER Level
0–99
Low Freq 0.04–1.00 [kHz]
Low Gain
-24–+12 [dB]
Mid Freq 0.25–9.99 [kHz]
Mid Gain -24–+12 [dB]
Mid Q 0.2–9.0
High Freq
0.80–9.99 [kHz]
High Gain
-24–+12 [dB]
HIGH Q 0.2–9.0
GM2 REVERB
Parameter Value
Character 0–5
Time 0–127
34
Explanation
LF damp attenuation amount (0: no
effect)
Frequency above which the high-
frequency portion of the reverb sound
is cut
HF damp attenuation amount (0: no
effect)
Explanation
Type of reverb
Amount of high-frequency attenuation
for the sound being input to the reverb
Time length of reverberation
Level at which the reverb sound is
returned to the input
Explanation
Room reverb. Higher values increase the
size of the room.
Hall reverb. Higher values increase the
size of the concert hall.
Plate reverb. A more flamboyant reverb
sound than P-A.
Plate reverb
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time length of reverberation
Adjusts the high-frequency portion of
the reverb.
Adjusts the density of the late
reverberation.
Adjusts the gain of the early reflections.
Adjusts the time of the early reflections.
Adjusts the density of the early
reflections.
Adjusts the volume of the early
reflections.
Frequency of the low range.
Gain of the low frequency range.
Adjusts the amount of mid-frequency
boost/cut.
Specifies the reference frequency of the
mid-frequency range.
Specifies the width of the mid-frequency
range.
Set a higher value for Q to narrow the
range to be affected.
Frequency of the high range.
Gain of the high frequency range.
Specifies the width of the high-frequency
range.
Set a higher value for Q to narrow the
range to be affected.
Explanation
Type of reverb
Time length of reverberation