Related Manuals for JC MACHINERY & TOOLS JC-GM-PLUS
Summary of Contents for JC MACHINERY & TOOLS JC-GM-PLUS
- Page 1 JC MACHINERY & TOOLS INC. Quality We Trust Roof Waterproofing Membrane Welding Machine JC-GM-PLUS User Manual ___________________________________________________________________ www.jc-tool.com info@jc-tool.com...
- Page 2 JC MACHINERY & TOOLS INC. Quality We Trust Please read this manual carefully before using this machine and keep it properly for future reference. Applications It can be applicable for welding PVC-P、 PE、 TPO、 ECB、 CSPE、 EPDM、 PVDF and other Coated fabric covering, foil and homogeneous or coating sealing film and PE coating fabric.
- Page 3 JC MACHINERY & TOOLS INC. Quality We Trust ● In order to prevent the machine from being damaged during transportation, the machine is fixed in the steel packing box with screws. When using the machine for the first time, it is necessary to loosen three machine fixing screws and take them out to remove the machine from the packing box, as shown in the figure above The handle can be pulled up and rotated, rotating so that...
- Page 4 JC MACHINERY & TOOLS INC. Quality We Trust Technical Parameters Voltage Frequency power 2000 Temperature 0～620℃ (32～1148℉) Welding speed 1～12 m/min Welding width 30/40 Size( L*W*H) 520*275*815 Weight ___________________________________________________________________ www.jc-tool.com info@jc-tool.com...
- Page 5 JC MACHINERY & TOOLS INC. Quality We Trust iii. Description 15 14 ___________________________________________________________________ www.jc-tool.com info@jc-tool.com...
- Page 6 JC MACHINERY & TOOLS INC. Quality We Trust Drive silica roller 11 Hot gun fixed slider Counterweight block 1 12 Hot gun positioning Counterweight block Drive roller handle Round belt 23. Universal wheel 13 Guide wheel 4. Nozzle 14 Guide wheel support Handrail block Pulley...
- Page 7 JC MACHINERY & TOOLS INC. Quality We Trust Controller Panel ● ON/OFF switch（38）is used for open the main power of the welder. ● Open ON/OFF switch (38), LCD display is shown as figure 1, the hot air blower is under natural wind without heating.
-
Page 8: Air Volume
JC MACHINERY & TOOLS INC. Quality We Trust Current temp. Current speed Setting temp. Setting speed Figure 1 Current temp. Current speed Setting temp. Setting speed Figure 2 Current temp. Current speed Setting temp. Setting speed Figure 3 VI. Welding parameters setting 1. - Page 9 JC MACHINERY & TOOLS INC. Quality We Trust The machine has a memory function parameters, namely when you use the ● welder next time, the welder will automatically use the last set of parameters without having to re-set parameters. VII. Positioning the welder Pressure Lift lever (30) to lift machine, move it to welding position (the edge of upper membrane should keep in the same alignment with Drive silica roller (1) and the edge of Guide wheel (13), as shown in figure 4.
- Page 10 JC MACHINERY & TOOLS INC. Quality We Trust VI. Using Condition 1. The distance between hot air nozzle and ground should be shown as figure 5（We have adjusted the distance）. 2. The distance between hot air nozzle and Drive roller should be shown as figure 6（We have adjusted the distance）.
- Page 11 JC MACHINERY & TOOLS INC. Quality We Trust VI. Welding steps 1. Setting welding parameters (see above). 2. When the temperature reaches the set value. 3. Welding machine positioning. 4. Pull up the positioning handle (12) of the air gun, lift the air gun (19), lower the air nozzle (4) and make it close to the submerged membrane.
- Page 12 JC MACHINERY & TOOLS INC. Quality We Trust __________________________________________________________________ www.jc-tool.com info@jc-tool.com...