1. Manuals
  2. Brands
  3. Mobeye Manuals
  4. Control Unit
  5. ThermoGuard CM2200
  6. User manual

Mobeye ThermoGuard CM2200 User Manual

Hide thumbs Also See for ThermoGuard CM2200:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
USER MANUAL
®
Mobeye
ThermoGuard
CM2200
SW version 1.n

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ThermoGuard CM2200 and is the answer not in the manual?

Questions and answers

Related Manuals for Mobeye ThermoGuard CM2200

Summary of Contents for Mobeye ThermoGuard CM2200

  • Page 1 USER MANUAL ® Mobeye ThermoGuard CM2200 SW version 1.n...
  • Page 2 In case of damage caused by disregarding the guidelines, the warranty expires. The user must regularly check the proper functioning of the device. The manufacturer cannot be ® held liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye device. Safety guidelines •...

  • Page 3: Table Of Contents

    CONTENT General description Getting started Place a SIM card Connect the temperature sensor to the unit Place the batteries Enter the program mode Program at least one telephone number Set a minimum and/or maximum temperature limit Switching on/off Use of inputs and external power supply Using the input(s) Using external power Extended options...

  • Page 4: General Description

    ‘Temperature OK’. - In case one of the inputs is activated by a sensor, the Mobeye ThermoGuard sends an alarm SMS text message and calls to the phone numbers as programmed by the user.

  • Page 5: Getting Started

    2. GETTING STARTED To get started with the Mobeye ThermoGuard at least the following steps need to be taken in following order: 1. Place SIM card (with PIN code 0000 or without PIN code) 2. Connect the temperature sensor to the unit 3.

  • Page 6: Program At Least One Telephone Number

    2.5 PROGRAM AT LEAST ONE TELEPHONE NUMBER The Mobeye ThermoGuard is able to send messages up to 5 telephone numbers. The first telephone number belongs to the administrator. Technical messages (like “battery low”) are sent to the administrator only. Without the administrators’ phone number, the Mobeye ThermoGuard cannot not function.

  • Page 7: Use Of Inputs And External Power Supply

    3.1 USING THE INPUT(S) It is possible to connect external sensors to the inputs. As a standard reaction after a triggered input, the Mobeye ThermoGuard sends an SMS text message to the preset numbers and calls these numbers. Insert the 2 wires of an external sensor through the hole of the enclosure to the inside part and next in the two connectors of input 1.

  • Page 8: Extended Options

    4. EXTENDED OPTIONS To program the Mobeye ThermoGuard, the GSM module must have network connection. In case only batteries are used, first switch the unit to the program mode. Next send SMS commands for the configuration. All settings are stored and will be kept in the unit, even in case the power supplies are removed.

  • Page 9: Possible General Settings

    This paragraph describes the general settings for the ThermoGuard. 4.4.1 Phone numbers The Mobeye ThermoGuard is able to send alarm messages up to 5 phone numbers. The first telephone number (TEL1) belongs to the administrator. Only this number receives all system messages.

  • Page 10: Alarm Text

    4.4.5 Alarm text Unique alarm texts can be programmed into the Mobeye ThermoGuard. User defined texts have a maximum length of 20 characters. Following default texts are programmed: Temperature below min. temp. <TEXT1>: Temperature too low: Temperature above max. temp. <TEXT2>:...

  • Page 11: Test Sms Text Message

    SMS command interval test message: <CODE> TEST:xx 4.4.11 Power failure SMS message In case the Mobeye ThermoGuard is powered externally and the power fails it sends an SMS text message to the administrator. The message is only sent in case the unit is armed.

  • Page 12: Reset Of System

    4.6 RESET OF SYSTEM To reset the Mobeye ThermoGuard to its factory settings: Remove the batteries Press the outside button while entering the batteries. Keep it pressed for (about) another 5 seconds Release the button immediately after the LED starts to flash After a successful reset, the status LED on the keypad will blink green to indicate that the module is not configured.

  • Page 13: Request Overview Of The Settings And Status

    Before sending the request, make sure the unit is in the program mode (please refer to 4.1). 5.1 STATUS REQUEST The status of the Mobeye ThermoGuard can be requested by sending an SMS with the content: <CODE> STATUS? Upon sending this request, the Mobeye ThermoGuard returns the status to the originator of the request.

  • Page 14: Technical Data En Status Feedback

    6. TECHNICAL DATA EN STATUS FEEDBACK Technical messages In case of a technical problem, the administrator receives an SMS message. Possible technical messages are: Message Reason Low batteries, external power Power is available, batteries need to be replaced supply OK No external power supply, batteries No external power supply, batteries are capable to take over operation in low power mode...
  • Page 15 Publisher. Reprinting, even in summary, is prohibited. This user manual meets the technical requirements at the moment of printing. Changes in technology and equipment are reserved. © Copyright 2013 by Mobeye, version CM2200EN130121...

Table of Contents