Table of Contents
Advertisement
SPECIFICATIONS
All units are factory programmed to the below specifications. Alteration should only be done by a factory trained technician or after
consultation with one of our technical representatives if you have any questions please contact:
Nuvia® Direct Phone Number: 951.734.7400
Service Related Matters: customerservice@Nuviawater.com
General questions: info@Nuviawater.com
NUVIA SIGNATURE Automatic Water Refiners
SIG Series 1" Dynamic Regeneration
Specifications
Optional - High Efficiency
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
Factory Settings - Standard Capacity
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
Optional - High Capacity
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
NW-HC70 Quantity - Cubic Feet
NW-C12 Refiner Quantity - Cubic Feet
Tank Size
Tank Jacket / Media Loaded
Brine Tank / Cabinet Size (Inches)
Sodium Storage Capacity
Flow Rate @ 15 psi Pressure Drop
Flow Rate @ 25 psi Pressure Drop
Back Wash Flow Rate
Shipping Weight
Regeneration Type
Maximum Efficiency
Plumbing Connections
Media Type
Electrical Requirements
Water Temperature
Water Pressure
Working Temperature: This unit must
be operated at temperatures between
40°F and 110°F (4°C - 43°C).
Working Pressure: This water refiner
must be operated on pressures
between 30 psi to 125 psi. If the water
pressure is higher than 125 PSI, use a
pressure reducing valve in the water
supply line to the refiner.
Voltage = 120V / 60 Hz
Pipe Size = 3/4", 1" and 1.25"
• At the stated service flow rates, the
pressure drop through these devices
will not exceed 15 psig.
• The manufacturer reserves the right
to make product improvements
which may deviate from the
Note: Nuvia® Systems can be installed into homes and small commercial applications with up to 1.25" plumbing. Optional 1.25"
connections available upon request.
NW-SIG-948-1.0
NW-SIG-1054-1.0
3.0 lbs
4.5 lbs
31.6 gal
44.3 gal
9,750
13,000
6.0 lbs
9.0 lbs
43.4 gal
62.7 gal
14,250
19,000
12.0 lbs
18.0 lbs
64.3 gal
90.3 gal
20,250
27,000
0.75 ft
1.0 ft
0.25 ft
0.50 ft
9x48
10x54
Yes
15.0²x34.7
15.0²x34.7
240 lbs
240 lbs
11.6 gpm
11.8 gpm
15.8 gpm
15.9 gpm
2.0 gpm
2.4 gpm
122 lbs
155 lbs
Includes 1" 90°Elbows & 1" Straight NPT
Input 120V 60 Hz - Output 12V 650mA
Min 39 - Max. 100 degrees Fahrenheit
specifications and descriptions
stated herein, without obligation to
change previously manufactured
products or to note the change.
* Do not use water that is
microbiologically unsafe without
adequate disinfection before or after
the system.
Peak flow rates intended for
intermittent use only (10 minutes
or less) and are for residential
applications only. Do not use peak flow
rate for commercial applications or for
a continuous rate when treated water
supplies are geothermal heat pump,
swimming pool, etc.
NW-SIG-1252-1.0
6.0 lbs
60.9 gal
19,500
12.0 lbs
87.1 gal
28,500
24.0 lbs
124.6 gal
40,500
1.5 ft
0.50 ft
12x52
Yes
No
15.0²x34.7
240 lbs
12.8 gpm
17.1 gpm
3.5 gpm
172 lbs
Dynamic Regeneration
4,333 grains /lb sodium
10% NW-HC70
Min. 20 - Max. 125 psi
For satisfactory operation, the
pumping rate of the well system must
equal or exceed indicated backwash
flow rate.
All units come with plastic bypass
Maximum Iron = 1.5 ppm
Maximum Hydrogen Sulfide = 0.0 ppm
Maximum Manganese = .75 ppm
pH = 6.5 to 8.5
MODELS:
NW-SIG-948-1.00
NW-SIG-1054-1.00
NW-SIG-1252-1.00
NW-SIG-1354-1.25
NW-SIG-1354-1.0
7.5 lbs
85.2 gal
26,000
15.0 lbs
116.2 gal
38,000
30.0 lbs
163.5 gal
54,000
2.0 ft
0.50 ft
13x54
No
23.0 x 40.5
420 lbs
13.0 gpm
17.2 gpm
4.0 gpm
208 lbs
5
Advertisement
Table of Contents
