Table of Contents
Advertisement
Alignments
The Service Alignment menu has the following items:
•
General, see General menu control
•
Options, see Options menu control
•
Option number, see Option number menu control
•
Store
8.3.1
General Menu Control
The General Menu has another 6 menu-items of which White
Drive and Luminance Delay have several sub-items.
•
White Drive
–
Testpattern : ON/OFF
–
Red
–
Green
–
Blue
•
Adjust Peak white Limiter
•
Input level Stereo Decoder
•
Stereo Channel Separation
•
Luminance Delays
–
Lum. Delay PAL
–
Lum. Delay SECAM
–
Lum. Delay NTSC
•
FBX Test Pattern : [ ON/OFF ]
•
Contrast
8.3.2
Options
Options are used to control the presence/absence of certain
features and hardware. There are two ways to change the
option settings. The various option configurations and the
descriptions of the codes are explained below.
Changing a single option:
A single option can be selected with the MENU UP/DOWN
keys and its setting can be changed with the MENU LEFT/
RIGHT keys.
Option Menu Control
The Options Menu has another 7 menu-items of which 5 items
have several sub-items.
•
TV Systems
–
FV916MG
–
FQ916MR
–
FQ916(D)MF
–
FQ916(D)ME
–
FQ936D
–
FQ944D
–
Chinese Tuner
–
FS988
•
Stereo Decoder
–
NICAM type [selection ]
–
Not available
–
BG or I
–
BG + I
–
Eco NICAM
–
2 CS [Yes/No ]
–
Global [Yes/No ]
•
Double Window
–
DW Available [ Yes/No ]
–
Mosaic [Yes/No ]
•
Video Repro
–
Combfilter [ Selection ]
–
Not Present
–
SAA4961
–
PalPlus [ Yes/No ]
•
Source Selection
–
SS type [ Selection ]
–
Europe
–
Global
•
Teletext
–
TXT [Yes/No]
–
PDC/VPS [Yes/No]
–
TXT Pre-set Table [Yes/No]
FTV1.9EE
•
Easy link [Yes/No ]
Changing multiple options by changing option word values (a
word is a 16-bit code).
An option word represents a number of different options.
Option number Menu control
The Options Number Menu control has another 2 menu-items
of which both items have several sub-items.
•
HardWare Option Numbers : 4 numbers of 5 digits
•
SoftWare Option Numbers
Detailed decription of the options per bit can be found at Figure
8-2 : Software Alignments.
Select one of the 4 HW-option words or one of the 2 SW option
word and key in the new value.
Changes in the options and options word setting are saved
when the set is switched to standby. Some changes will only
take effect after the set has been switched OFF and ON again
with the mains switch.
Option bits/word
HW options code 1: bits 15,14, ..., 1,0 :
HW options code 2: bits 15,14, ..., 1,0 :
HW options code 3: bits 15,14, ..., 1,0 :
HW options code 3: bits 15,14, ..., 1,0 :
SW options code 1: bits 15,14, ..., 1,0 :
SW options code 2: bits 15,14, ..., 1,0 :
An option word value is calculated in the following way:
value "option bit 0" x 1 =
value "option bit 1" x 2 =
value "option bit 2" x 4 =
value "option bit 3" x 8 =
value "option bit 4" x 16 =
value "option bit 5" x 32 =
value "option bit 6" x 64 =
value "option bit 7" x 128 =
value "option bit 8" x 256 =
value "option bit 9" x 512 =
value "option bit 10" x 1024 =
value "option bit 11" x 2048 =
value "option bit 12" x 4096 =
value "option bit 13" x 8192 =
value "option bit 14" x 16384 =
value "option bit 15" x 32768 =
Total : value "option word" =
The table below shows the default values of the hardware (HW)
and software (SW) options for the West European sets ( /12)
and for the France sets (/19).
Destination
PALplus
Europe
No
"
Yes
France
No
"
Yes
8.
GB 77
: 2 numbers of 5 digits
HW Option
SW Option
number
Number
01024
00000
14353
04884
10624
16452
01024
00000
14353
04884
14592
16452
01025
00000
14353
04884
10624
16452
01025
00000
14353
04884
14592
16452
Advertisement
Table of Contents
