Maintenance & Service Section Specifications Page Specifications & Warranty Appendix 1 – Additional SPD131DDA System Set-ups Appendix 2 – Additional SPD131DDA System Set-ups For DMSO Appendix 3 – RS232 Port Specifications Disclaimer: All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, or responsibility of any kind, expressed or implied. Statements or suggestions possible use of our products are made without representation that any such use is free of patent infringement and are not recommendations to infringe any patent.
Overview of the SPD131 DDA Unit Figure 1 = Front View Figure 2 = Side View Figure 3 = Back View Fig. 1 Top Radiant Cover Control Panel Front Panel Left Side Panel Anti Skid/Vibration Right Side Panel Chamber View Window Vacuum Port Vacuum Tubing Fig.
COVER LOCK OVERRIDE To Open The Top Cover During Power Failure: Remove the philips screw holding the cover lock, release cord and lightly pull it as shown, while lifting the cover.
Unviersal Vacuum Source What it should look like: ® How To Hook Up The SPD131DDA SpeedVac System Unpack unit from the box and verify that all the parts match packing list. Read instruction manual carefully! If assistance is required, contact Customer Service.
CONTROL PANEL Level Manual Pre- Select Heat Ramp Vacuu Auto Modify Setpoints View On/Off Description of Control Panel PRE-HEAT - use to pre-heat chamber to 45 C prior to beginning or between runs. ° Once run is initiated the pre-heat stops. RC ON/OFF - Use to add radiant heat to chamber.
Page 8
TIME DISPLAYS - Indicates heat timer or run timer set-points. In the process of a run it indicates elapsed time or time left. Set from 0.01 [1 min.] to 9.59 [9 hours, 59 minutes] or “CCC” [continuous]. VACUUM PRESSURE DISPLAY - Displays vacuum level or ramp. Chamber vacuum is displayed in torrs or millitorrs by shifting a decimal point.
Press R/C for radiant chamber heat. Press at any time to turn OFF and ON. (As long as there is time left in the heat timer). To end the manual run, press “STOP” button. The display will show “End” , the valves will click, isolating the chamber from the vacuum pump and also allowing air to bleed into the chamber.
Page 10
Press R/C for radiant chamber heat. Press at any time to turn OFF and ON. (As long as there is time left in the heat timer). Once the time decrements to 0.00 HRS. the run will automatically stop, the display will show “End” ,the SAV valves will click, also allowing air to bleed into the chamber.
MAINTENANCE/SERVICE 1. Maintenance: The SPD131DDA SpeedVac requires no scheduled maintenance. 2. Cleaning: The SPD131DDA SpeedVac should be cleaned if solvent, spills on or inside the unit. Clean up any spills immediately using absorbent towels. Always wear gloves when cleaning and dispose used of paper towel in appropriate designated refuse containers.
SPECIFICATIONS SPD131DDA Model: Integrated Automatic Bleeder lve Bleeder Valve: Temperature Range: 45°C-80°C Volume Range/Tube: 18 x 150 mm* Tube Capacity: Maximum Carrier Capacity: 2 x (96-deepwell plates) Dimensions: (W x D x H) in.: 14 x 18 x 13 36 x 45 x 33 Weight: lbs.
Page 15
APPENDIX 1 Additional SPD 131 DDA System Set-ups SpeedVac Concentrator ® SPD131DDA (Back view of Concentrator) *Vacuum Tubing Carrying Vapors From SPD131 DDA to RVT405DDA *Vacuum tubing MUST be connected so that there is no dips or bends that will collect ANT100 condensed DMSO.
Page 16
APPENDIX 2 Additional SPD 131 DDA System Set-ups for DMSO Applications SpeedVac Concentrator ® SPD131DDA (Back view of Concentrator) Vacuum Tubing From SPD131 DDA to Vacuum Tubing OFP400 From RVT4104 to SPD131DDA SPD131DDA *Vacuum Tubing Carrying Vapors From SPD131 DDA to RVT405DDA...
APPENDIX 3 RS232 Port Specifications Baud Rate: 9600 Parity : None Bits: Stop Bit: Data Format: *ALL X’s are numerals from 0-9. X X__ (space) _ X.XX (space) X.XX (space) __ XX.X(space) sequence repeats The first field (XX) indicates temperature in C.
Page 18
WEEE Compliance WEEE Compliance. This product is required to comply with the European Great Britain Union’s Waste Electrical & Electronic Equipment (WEEE) Directive 2002/96EC. It is marked with the following symbol. Thermo Fisher Scientific has contracted with one or more recycling/disposal companies in each EU Member State, and this product should be disposed of or recycled through them.
Page 19
Important For your future reference and when contacting the factory, please have the following information readily available: Model Number: Serial Number: Date Purchased: The above information can be found on the dataplate attached to the equipment. If available, please provide the date purchased, the source of purchase (manufacturer or specific agent/rep organization), and purchase order number.
Page 20
Thermo Fisher Scientific Inc. 275 Aiken Road Asheville, NC 28804 United States www.thermofisher.com 197-3003-00 Rev G...