Da-Lite Advantage Electrol Instruction Book
  1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projection Screen
  5. ADVANTAGE ELECTROL
  6. Instruction book

Da-Lite Advantage Electrol Instruction Book

Hide thumbs Also See for Advantage Electrol:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION BOOK FOR
Advantage
Electrol
®
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Advantage Electrol and is the answer not in the manual?

Questions and answers

Related Manuals for Da-Lite Advantage Electrol

Summary of Contents for Da-Lite Advantage Electrol

  • Page 1 INSTRUCTION BOOK FOR Advantage Electrol ® ®...

  • Page 2: Important Safety Instructions

    Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Da-Lite® is a registered trademark of Milestone AV Technologies. All rights reserved. Important Safety Instructions When using your video equipment, basic safety precautions 10.
  • Page 3 Advantage Electrol Suggested Methods of Installation ® ® Method 1 6 1/16" 6 7/16" 7 3/4" Variable Position Mounting Bracket 9 1/4" Audience Side Motor 6 1/16" 3/8" Threaded Rod (Not Included) Electrical Attached To Junction Box Mounting Bracket 6 3/8" Self-Trimming Finished Flange...

  • Page 4: Tools Required For Installation

    If your case was ordered in advance of the screen and See Suggested Methods of Installation. roller assembly, your installation is now complete. Continue to step 4 if your Advantage Electrol was ordered 2. Tighten bolts until trim flange is flush with ceiling. as a complete unit.
  • Page 5 Screen and Roller Assembly Installation Follow these steps if your screen and roller assembly was ordered separately from the case. 6. Complete electrical hook-up by snapping motor wire Remove the access door. First, remove the 2 screws from the ends. Be sure to support the door during this step to avoid connector into case connector (Figure 2).
  • Page 6 Rated torque of model DL45EQ-6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. off. Motor is intended for use in Da-Lite screens incorporating a 3.00" and 3.25" roller diameter. Make sure motor collar is on motor.
  • Page 7 Advantage Electrol Installation For 120V Screens ® ® 120V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is 3-conductor 20–24 gauge wire can be used in place of the S T O used.
  • Page 8 Advantage Electrol Installation for 220V Screens ® ® 220V Wiring Diagram with Operation & Limit Adjustment IMPORTANT NOTE: The wall switch is REQUIRED to make any Wall Switch limit switch adjustments, EVEN if a third party control system is S T O used.
  • Page 9 Advantage Electrol Installation for 220V Screens (continued) ® ® 220V Wiring Diagram with European Style Wall Switch IMPORTANT NOTE: The European style wall switch is for operation only and CANNOT be used to make limit switch Use 3-conductor 20–24 gauge wire for wall switch connections. adjustments.
  • Page 10 Optional Built-In Video Projector Interface CAUTION: The projector must be turned off before IMPORTANT NOTE: The wall switch is REQUIRED to make any connecting the trigger wires to the projector. Failure to limit switch adjustments, EVEN if a third party control system is do so may damage the controller.

  • Page 11: Screen Adjustment

    Screen Adjustment If your Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the Wiring Diagram.

  • Page 12: Operation Of Screen

    Operation of Screen Operation & Limit Adjustment Wall Switch “Up” Button Press ”DOWN” button on screen switch and screen will deploy out of case in downward direction. “Stop” Button 2. Press “STOP “button on screen switch and screen will stop if in movement.
  • Page 13 Conditions for Transportation and Storage • Temperature: Between 40 - 1000F (5 - 400C) • Make sure the entire package is supported when stored • Relative Humidity: 30% to 70%, non-condensing • Do not stack more than six projection screens on top of each other •...

  • Page 14: Troubleshooting

    Troubleshooting Symptom Cause Solution Verify 115-125V (or 220-240V). If insufficient voltage, rewire Incorrect line voltage. incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections.
  • Page 16 Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

Table of Contents