Page 1
REPRODUCTION OF THIS MANUAL IN ANY FORM WITHOUT WRITTEN APPROVAL OF BAILEIGH INDUSTRIAL LTD IS PROHIBITED. Baileigh Industrial LTD does not assume and hereby disclaims any liability for any damage or loss caused by an omission or error in this Operator’s Manual, resulting from accident, negligence, or other occurrence.
Table of Contents STANDARD TERMS AND CONDITIONS OF SALE ............1 INTRODUCTION ......................6 GENERAL NOTES ......................6 SAFETY INSTRUCTIONS ....................7 SAFETY PRECAUTIONS ....................9 Dear Valued Customer: ....................9 TECHNICAL SPECIFICATIONS ................... 11 TECHNICAL SUPPORT ....................11 UNPACKING AND CHECKING CONTENTS ..............12 Cleaning ........................
BAILEIGH INDUSTRIAL LTD. Unit D Swift Point Swift Valley Industrial Estate, Rugby West Midlands, CV21 1QH United Kingdom Phone: 024 7661 9267 Fax: 024 7661 9276 sales@baileigh.co.uk www.baileigh.co.uk STANDARD TERMS AND CONDITIONS OF SALE TABLE OF CONTENTS 1 INTERPRETATION ....................2 2 APPLICATION OF TERMS ..................
Buyer relating to the Goods; “Company” Baileigh Industrial Limited, a company incorporated in England and Wales (Company Number 05672861) whose registered office is at Unit D Swift Point, Swift Valley Industrial Estate, Rugby, West Midland, CV21 2QH “Company Materials”...
NON-DELIVERY The quantity of any consignment of Goods as recorded by the Company upon dispatch from the Company’s place of business shall be conclusive evidence of the quantity received by the Buyer on delivery unless the Buyer can provide conclusive evidence proving the contrary.
WARRANTY The Company warrants that (subject to the other provisions of these Conditions) upon delivery, and for a period of 12 months from the date of delivery, the Goods will be of satisfactory quality within the meaning of the Sale of Goods Act 1994. Warranty provisions are strictly at the determination of the Company on a case by case basis.
ASSIGNMENT 13.1 The Buyer shall not be entitled to assign the Contract or any part of it without the prior written consent of the Company. 13.2 The Company may assign the Contract or any part of it to any person, firm or company. FORCE MAJEURE The Company reserves the right to defer the date of delivery or to cancel the Contract or reduce the volume of the Goods ordered by the Buyer (without liability to the Buyer) if it is prevented from or delayed in the carrying on of its business due to circumstances beyond the...
After receiving your equipment remove the protective container. Do a complete visual inspection, and if damage is noted, photograph it for insurance claims and contact your carrier at once, requesting inspection. Also contact Baileigh Industrial and inform them of the unexpected occurrence. Temporarily suspend installation.
IMPORTANT PLEASE READ THIS OPERATORS MANUAL CAREFULLY It contains important safety information, instructions, and necessary operating procedures. The continual observance of these procedures will help increase your production and extend the life of the equipment. SAFETY INSTRUCTIONS LEARN TO RECOGNIZE SAFETY INFORMATION This is the safety alert symbol.
Page 10
SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. PROTECT EYES Wear safety glasses or suitable eye protection when working on or around machinery. PROTECT AGAINST NOISE Prolonged exposure to loud noise can cause impairment or loss of hearing.
Baileigh does not recommend or endorse making any modifications or alterations to a Baileigh machine. Modifications or alterations to a machine may pose a substantial risk of injury to the operator or others and may do substantial damage to the machine.
Page 12
7. DO NOT use electrically powered tools in the presence of flammable gases or liquids. Power tools create sparks that may ignite flammable materials or gases. 8. Tooling adjustments and maintenance. Always keep tooling sharp and properly adjusted for optimum performance. 9.
For specific application needs or future machine purchases contact the Sales Department at: +44 (0)24 7661 9267 or sales@baileigh.co.uk. Note: The photos and illustrations used in this manual are representative only and may not depict the actual color, labeling or accessories and may be intended to illustrate technique only.
UNPACKING AND CHECKING CONTENTS Your Baileigh machine is shipped complete. Separate all parts from the packing material and check each item carefully. Make certain all items are accounted for before discarding any packing material. WARNING: SUFFOCATION HAZARD! Immediately discard any plastic bags and packing materials to eliminate choking and suffocation hazards to children and animals.
ELECTRICAL ATTENTION: HAVE ELECTRICAL UTILITIES CONNECTED TO MACHINE BY A CERTIFIED ELECTRICIAN! Your Baileigh Machine is Check if the available power supply is the same as required by the machine (consult nameplate on machine) WARNING: Make sure the grounding wire (green) is properly connected to avoid electric shock.
Page 17
• Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
DAILY TOOL USE AND CARE REQUIREMENTS • DO NOT touch the cutter while it is in motion. Always follow the personal protection equipment recommendations while operating this tool. • Always use both hands to operate the tool. • Always ensure that the material you are working on is securely clamped. •...
MACHINE SET-UP; INSTALLING CUTTERS WARNING: For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. 1. To insert a cutter, first insert the pilot pin, and then slide the cutter into the adaptor. Align the proper flat with the locking screw and tighten securely with the supplied hex wrench.
OPERATION CAUTION: Always wear proper eye protection with side shields, safety footwear, and leather gloves to protect from burrs and sharp edges. When handling large heavy material make sure they are properly supported. This machine is designed specifically for drilling holes in mild steel using the appropriate cutters and accessories.
7. Switch the Forward/Reverse switch to the desired direction of rotation. 8. With the motor head in the raised position, switch on the motor and allow it to come up to full speed. 9. Turn the crank handle to begin cutting use light pressure at first to keep bit from wandering, and then continue with normal pressure.
Troubleshooting In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug, excessive sparking may indicate the presence of dirt in the mater or worn out carbon brushes. Note: Proper maintenance can increase the life expectancy of your machine. Adjusting Slides Free Play Periodically check, lubricate, and adjust as necessary.