Page 1
Yale Assure Lever Key Free Push Button ® ™ Installation and Programming Instructions ® (YRL236) #8-32 x 5/16" Machine screws #7 wood & #8-32 machine x 20mm M4 x 22mm Combination screws Pan head machine screws AA Alkaline Batteries Battery Cover...
Page 2
Preparing to Install Tools Needed Standard Phillips Head Screwdriver Tools necessary only for new doors or adjusting existing prep. Template Tape Pencil Measure Drill Wood Mortise Chisel Utility Knife Level P/N YRL-LKFPBINSTL-FUL Rev A...
Page 3
Checking Measurements 2-3/8" or 2-3/4" (60mm or 70mm) Backset 2-1/8" (54mm) Diameter 1-3/8" or 1-3/4" (35mm or 44.5mm) Door Thickness 1" (25mm) Diameter P/N YRL-LKFPBINSTL-FUL Rev A...
Page 4
Determining Door Handing Inswinging Door Outswinging Door Interior Left Hand Right Hand Interior Reverse Reverse Left Hand Right Hand Exterior Exterior Face a door swinging open Face a door swinging open away from you. toward you. If it swings open to the right, If it swings open to the right, it it is a right hand door.
Page 5
Preparing Door & Frame Necessary for new doors or adjusting existing prep. 2-1/8" (54mm) Dia. 2-3/8" (60mm) 1" (25mm) 2-3/4" (70mm) Dia. Backset Drill holes 1/2 way through door then complete from other side to prevent splitting. Frame Frame Inside of Door 1"...
Page 6
Installing Latch & Strike Plate Right Hand Installation Shown 2-3/8" through bolt posts default PULL 2-3/4" through bolt posts Note: Adjustment based on backset optional Outside of Door Frame *Backset *2-3/8" (60mm) 2-3/4" (70mm) P/N YRL-LKFPBINSTL-FUL Rev A...
Page 7
Installing Push Button Right Hand Installation Shown “TOP” mark must be on top surface and tailpiece in vertical position. Incorrect orientation will cause lock to fail. Outside of Right Hand Door Inside of Right Hand Door P/N YRL-LKFPBINSTL-FUL Rev A...
Page 8
Installing Interior Mounting Plate Right Hand Installation Shown Inside of Right Hand Door Inside of Right Hand Door P/N YRL-LKFPBINSTL-FUL Rev A...
Page 9
Attaching the Cable Assembly Right Hand Installation Shown Ensure cable is securely fastened into adapter. Inside of Right Hand Door Use cable hooks for proper cable routing. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 10
Installing Interior Lock Right Hand Installation Shown Inside of Right Hand Door “Click” P/N YRL-LKFPBINSTL-FUL Rev A...
Page 11
Installing Exterior Key Free Cylinder Outside of Right Hand Door Latch Key free cylinder must be installed with bar away from latch. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 12
Installing Exterior Lever Outside of Right Hand Door Press pin while installing lever so lock is not damaged. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 13
Installing Interior Lever Inside of Right Hand Door Press pin while installing lever so lock is not damaged. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 14
Testing Mechanical Operation Test interior and exterior operation with door open. Outside of Right Hand Door Outside of Right Hand Door Test thumbturn and both levers in locked and unlocked positions. If operation fails, check installation beginning with Step 3 and refer to Hardware Troubleshooting.
Page 15
Installing Optional Smart Module (if included) Inside of Right Hand Door Batteries must not be installed prior to inserting and/or removing module. NOTE: If a Smart module was included with your lock, it is in a separate box with additional module installation instructions.
Page 16
Installing Batteries & Cover Inside of Right Hand Door Congratulations, you've installed the ™ ® Yale Assure Lever Key Free Push Button ( YRL236 Programming Instructions will help you customize your product. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 17
Testing Push Button Operation Test with door open. A Master Enty Code must be created upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. See of Programming Instructions below.
Page 18
Resetting Lock to Factory Default Interior Lock Reset Button When resetting the lock, all user codes, including the Master Entry Code*, are deleted. All programming features are reset to original default settings. See “Factory Settings”. 1. Remove the battery cover and batteries. 2.
Page 19
(9-Volt battery jumper, low battery warnings), it is still possible for a lockout situation to occur. Because this product does not ® have a mechanical override (a key), Yale recommends to use this product in an environment where there are additional entry points into the dwelling.
Page 20
Hardware Troubleshooting Cycle lock in both the locked and unlocked positions. If problems are found: Tailpiece and spindle will not mate and fit into the interior escutcheon a. Ensure that your door is between 1-3/8" and 1-3/4" thick b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards c.
Page 21
Programming Instructions Speaker Master Entry Code must be created before any further programming. Max User Codes = 250 with Smart Module and 25 without. P/N YRL-LKFPBINSTL-FUL Rev A...
Page 22
Creating Master Entry Code Creating a Master Entry Code must be performed upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. Press Press Press Enter 4-8 digit Master Entry Code.
Page 23
Creating User Entry Codes Master Entry Code must be created first. *Max user codes = 250 with Smart Module and 25 without. Enter Master Entry Code Press Press Enter 4-8 digit Entry Code Press Press Press Press (code flashes) Adding more User Codes: To end programming: Press Press...
Page 24
Unlocking Door with Entry Code Enter Entry Code Press Code Chart Duplicate if necessary Entry Code Management Entry Code Master: User Name: P/N YRL-LKFPBINSTL-FUL Rev A...
Page 25
Advanced Lock Settings (Main Menu selection #3). Low Battery: When battery power is low, the Yale logo button lights RED when unit is used. If battery power is completely lost, use the 9Volt battery override. To use the 9V battery override apply 9V battery, in either direction, to terminals below the keypad for backup power option.
Page 26
Feature Programming Through Menu Mode Using Master Entry Code* 1. Enter 4-8 digit Master Entry Code* followed by key. 2. Enter digit corresponding to the function to be performed followed by the key. *The Master Entry Code must be created prior to any other programming of the lock. Master PIN Code Setting User PIN Code Registration Register...
Page 27
Programming Troubleshooting Symptom Suggested Action * When batteries are replaced, Smart Module locks have a real time clock that will be set through the User Interface (UI); it is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time (DST). P/N YRL-LKFPBINSTL-FUL Rev A...
Page 28
Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. Product Support Tel 1-855-213-5841 • www.yalehome.com Yale® and Yale Real Living® are registered trademarks of ASSA ABLOY Residential Group, Inc. Assure Lever™ is a trademark of ASSA ABLOY Residential Group, Inc.
Page 29
Yale Z -Wave Plus Module ® ® ® Installation and Programming Instructions Installing the Z -Wave Plus Module ® IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: • Remove battery cover and batteries. • Remove and/or insert Network Module.