Table of Contents
Advertisement
Quick Links
Certification N:o VTT 14 ATEX 041X and IECEx VTT 14.0004X
Thank you for choosing SLAM
site. Purpose of this manual is to provide you all the necessary safety and product information
to conduct your job conveniently and without any risks for health and safety.
Instructions for Safe Use
®
Hornet –portable work light with battery back up for your job
SLAM
SLAM
®
Hornet EM 1LED
®
Hornet EXIT 1LED
Distributed by: Saurya HSE Pvt Ltd
HO: C-112 A Kailash Business Park,
Veer Sawarkar Marg, Vikhroli West, Mumbai 400079, India
T : +91 22 4065 5555 | E: info@sauryahse.com | W: sauryahse.com
Advertisement
Table of Contents
Summary of Contents for Saurya SLAM Hornet EM 1LED
-
Page 1: Instructions For Safe Use
Hornet EM 1LED ® SLAM Hornet EXIT 1LED Distributed by: Saurya HSE Pvt Ltd HO: C-112 A Kailash Business Park, Veer Sawarkar Marg, Vikhroli West, Mumbai 400079, India T : +91 22 4065 5555 | E: info@sauryahse.com | W: sauryahse.com... -
Page 2: Table Of Contents
2/16 Contents Instructions for Safe Use .............................1 ® Introduction to SLAM Hornet ........................3 Technical data .............................3 Certification of equipment ........................3 Standard unit construction ........................5 Quality guaranteed ..........................6 1.4.1 General ............................6 1.4.2 Individual testing reports ........................6 Prior to use ..............................7 Selection of right equipment ........................7 Intended purpose of equipment ......................7 Application of use (Zone XX) in accordance with equipment category ..........7 Explosion group (IIA, IIB or IIC) in accordance with Equipment group (IIA, IIB or IIC) ......7... -
Page 3: Introduction To Slam ® Hornet
3/16 ® 1. Introduction to SLAM Hornet This instruction manual guides you through the process of selecting and adopting SLAM® Hornet with battery back up work light at your work site. The manual regards the following SLAM® Hornet types: Technical data ®... - Page 4 4/16 II 2 G Ex e ib mb op is IIC T4 Gb 0537 II 2 D Ex tb op is IIIC T90 ° C Db IP 66 = Valid production quality system approved and notified by VTT (Finnish Notified Body, listed 0537 by EC) = Certified for explosion hazardous areas...
-
Page 5: Standard Unit Construction
5/16 Standard unit construction The following list familiarizes you with some common unit features important to recognize. End parts: Flexible, plastic-made end parts ensure shock-absorbing and harmless contact to sensitive and hard surface in case the luminary drops to the ground even from high position. Light construction affects the total weight of the unit itself. -
Page 6: Quality Guaranteed
6/16 Quality guaranteed 1.4.1 General ® The SLAM Hornet series is designed, certified, manufactured and tested under ISO 9001:2008 quality system as well as additional requirements of the Directive 94/9/EC (ATEX) or IECEx scheme. ® The SLAM Hornet series is designed and tested according to the latest directives and standards. The referred directives and standards of the production date in case are stated on the Declaration of Conformity included in the delivery. -
Page 7: Prior To Use
7/16 2. Prior to use Selection of right equipment You need to be sure that the equipment you intend to take into explosion-hazardous area matches up with the zone classification and other safety requirements related. The operator is solely responsible for the correct selection and use of the equipment at his site. At least the following points should be notified prior to use: Intended purpose of equipment Please keep in mind what the actual application of equipment is. -
Page 8: Temperature Class Of The Equipment
8/16 Temperature class of the equipment Please observe the Ignition Temperature (IT) of the substance creating the explosion hazard at your site. Select the equipment based on IT of the substance. The temperature of the equipment must be lower than IT. The highest temperature of the equipment is specified by using Temperature Classes T1 to T6. -
Page 9: Operating Instructions
9/16 3. Operating instructions Personnel The use of the equipment is to be controlled and accepted by the operator. The personnel using the unit have to be authorized by the operator or his representative. In case of further training of using the equipment please contact the local supplier of this equipment. -
Page 10: Connection To The Supply
10/16 Note! Lack of equipotential bonding may cause danger in Ex –area, therefore please pay special attention to all installations of yours involving metallic parts. Static charging is especially noted on standards referring to installations in explosion hazardous areas (e.g. EN/IEC 60079-14). Connection to the supply It is recommended that the unit is first connected to the mains / transformer before entering the explosion hazardous area. - Page 11 11/16 In-built sockets are recommended when the illuminated area is notably large, complex or not enough wiring points are available. Linking the units in series save time, amount of cable and provide an opportunity to build a chain of lights to provide enough illumination in the darkness. ®...
-
Page 12: Special Operating Features Of Shem
12/16 Voltage peaks are more harmful and may damage the ballast permanently when subjected to excessive peaks continuously. If fluorescent tubes are flickering when the units are chained up, it may be due to excessive linking. This may shorten notably the lifetime of fluorescent tube. Unplug the last unit on the line to ensure proper function of the unit. -
Page 13: Inspection & Maintenance
13/16 Powered / Battery full 4. Inspection & Maintenance After Use Take the following steps after the SHEM -unit has been taken out from Ex-area: 1) Clean the unit with a damp cloth (do not use detergents or solvents) 2) Change the anti-static film if only little light comes through it or it is damaged 3) Have a visual check on the unit (condition of cable, PC-tube, tightness of parts) 4) Let the unit dry in open air Maintenance... -
Page 14: Repair Report
14/16 · High-voltage test (500 VDC between Phase & Neutral against P/E conductor) · Operational test · Test of expected use (vibrations, shaking) Proper testing ensures safe operation of repaired equipment. Repair report The operator is responsible for keeping up to date record of the condition of his equipment (EN/IEC 60079-14). - Page 15 15/16...
-
Page 16: Helpdesk
Helpdesk Under any doubt or question, please contact your local distributor or the manufacturer. Contact details: Distributed by: Saurya HSE Pvt Ltd HO: C-112 A Kailash Business Park, Veer Sawarkar Marg, Vikhroli West, Mumbai 400079, India T : +91 22 4065 5555 | E: info@sauryahse.com | W: sauryahse.com...