Troubleshooting Guide - Polygroup SUMMER WAVES RP350 Owner's Manual

WARNING:
TURN OFF THE PUMP AND UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
SYMPTOM
A Unit not plugged in or
Motor fails to
1 start or kicks
B GFCI Plug and/or circuit
on and off
C Low voltage
A Low pool water level
No flow or slow
B Inlet/Outlet clogged
water flow through
2
the return hose.
C Dirty filter cartridge
A Chlorine level is not in
the suitable range.
B pH level is not in the
suitable range.
C Dirty filter cartridge
Filter pump is not
cleaning the pool
3
D Damaged filter cartridge
properly. (water
cloudy, green, etc...
E Slow water flow
F Other Chemicals Required
G Pool water very dirty
A Hose area:
Return hose do not fit well
on canister connections and/
or wall fitting connections
4 Water leakage
B Vent screw in Seal Top
C Seal Top
POOL PUMP DISASSEMBLY & STORAGE
1. First turn the pump off and unplug the main power cord of the system. Remove the RF Diverter
with the RF Plug 8 Now, hand tighten the SF Cap
2. Slowly unscrew the Vent Screw
3. Remove the Seal Top 14 by turning counter-clockwise.
4. Remove the Filter Cartridge 18
5. Loosen all four Hose Clamps 10
6. Clean and dry all filter pump parts including filter cartridges.
7. Liberally lubricate the O-rings 13
Vent Screw 12 onto the Canister
8. All items should be stored in a dry environment that remains above 32 degrees Fahrenheit at all times.
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8 AM to 5 PM Mon. thru Fri.
14

TROUBLESHOOTING GUIDE

CAUSE
A Unit must be plugged into a 3-wire grounded power outlet. Press the reset button on the
GFCI not activated
B Reset the GFCI plug and/or circuit breaker. If problem persists, have the circuit
breaker tripped
C Check the line voltage, it must be in the range of 105 to 125 Volts A.C.
A Fill the pool to the fill line. The suction fitting must be at least 4" under water.
B Check for obstructions in the suction hose or fitting and in the return hose or fitting.
C Clean or replace the filter cartridge (See page 12). A spare cartridge makes service more
A Maintain chlorine level between 1.0 to 1.6 ppm.
B Maintain pH level between 7.3 to 7.8.
C Clean or replace the filter cartridge (See page 12). A spare cartridge makes service more
convenient
D Inspect the filter cartridge for holes or tears. If visibly damaged; replace the filter cartridge
E Check for obstructions in the suction hose or fitting and in the return hose or fitting.
F Have water tested at pool supply store. It may be necessary to add other chemicals due to
G Chemicals are required to maintain clean pool water. Clean pool and filter more often.
Suction or
A Make sure the hose clamp
to ensure a proper seal. Adjust hose clamp, check o-ring and re-tighten.
Check hose for any holes or cracks and replace if needed.
B Check O-ring
C Check O-ring
5 onto the Suction Fitting
12 from the Seal Top 14 allowing the Filter Pump to depressurize.
and remove any chlorine tablets left inside the core section of the filter.
, remove the Hoses 9 and allow the water to drain out.
at the Seal Top 14 and Gasket
16 . Store all parts carefully in an airtight plastic bag.
MST. Extended operating days and hours during peak season requirements.
GFCI to start the pump.
checked by a qualified electrician.
convenient.
varying water quality in different localities.
is positioned properly over the hose and O-ring
13 for damage. Replace if needed. Tighen the Vent Screw
15 for damage. Replace if needed. Tighten the Seal Top
7 from the Return Fitting
2 .
15 on the Canister 16 with petroleum jelly, and then reassemble it along with the Seal Top
SOLUTION
6 and then plug the Return Fitting
12 .
14 .
6
14 ,