Kusam-meco KM-459 Operation Manual
  1. Manuals
  2. Brands
  3. Kusam-meco Manuals
  4. Multimeter
  5. KM-459
  6. Operation manual

Kusam-meco KM-459 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
LIST OF PRODUCTS
 Digital Multimeter
 Digital AC & AC/DC Clampmeter
 AC Clamp Adaptor
 AC/DC Current Adaptor
 Thermo Anemometer
 Thermo Hygrometer
 Distance Meter
 Digital Lux Meter
 Network Cable Tester
 Power Factor Regulator
 Earth Resistance Tester
 Digital Panel Meters
 DC Power Supplies
 High Voltage Detector
 Calibrators
 Gas Analysers
 Frequency Counter
 Function Generator
 Phasing Sticks
 Battery Tester
 Waterproof Pen Testers
 Solar Power Meter
 EMF Detector
 Wood, Paper & Grain Moisture Meter
 Transistorised Electronic Analog & Digital Insulation
Resistance Testers(upto 10 KV)
 Digital Sound Level Meter & Sound Level Calibrator
 Digital contact & Non-contact Type Tachometer
 Digital Non-contact (infrared) Thermometer
 Maximum Demand Controller/Digital Power Meter
 Digital Hand Held Temperature Indicators
G 17, Bharat Industrial Estate, T. J. Road,
Sewree (W), Mumbai - 400 015. INDIA.
Sales Direct :
(022) 24156638
Tel. :
(022) 24124540, 24181649.
Email :
kusam_meco@vsnl.net
Website :
www.
kusamelectrical.com
www.kusam-meco.co.in
®
Fax :
(022) 24149659
AN ISO 9001:2015 COMPANY
MODEL KM-459
APO RS232 R MAX-MIN
R Q
AUTO H SET
TOL AVG
D
PAL SER
LC
R
0
FREQ
1
2
RANGE
4
5
MIN
HOLD
MAX
7
8
Hi o L
／
REL
LIMITS
DO NOT APPLY VOLTAGE TO INPUT TERMINALS
DISCHARGE CAPACITOR BEFORE TESTING
AUTO-POWER OFF
OPERATION MANUAL
®
LCR METER
DUAL DISPLAY
%
1kHz
120Hz
%
mH
m npF
ENTER
PAL
SER
3
6
SET
9
TOL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KM-459 and is the answer not in the manual?

Questions and answers

Related Manuals for Kusam-meco KM-459

Summary of Contents for Kusam-meco KM-459

  • Page 1  Earth Resistance Tester  Digital Panel Meters  DC Power Supplies  High Voltage Detector  Calibrators  Gas Analysers MODEL KM-459  Frequency Counter  Function Generator  Phasing Sticks  Battery Tester  Waterproof Pen Testers  Solar Power Meter ...

  • Page 2: General Specification

    ® ® GENERAL SPECIFICATION CONTENTS • 4½ digit liquid crystal display (LCD). Display: Overload indication: • “OL” display. Page Title Low battery indication: • The “ ” is displayed when the battery voltage drops below the operating level, GENERAL SPECIFICATION and cancel all the memorized values to PANEL ILLUSTRATION store into EEPROM.

  • Page 3: Panel Illustration

    ® ® PANEL ILLUSTRATION LCR METER DUAL DISPLAY Second APO RS232 R MAX-MIN AUTO H SET TOL AVG Display PAL SER 1kHz 120Hz Main Display m npF ENTER FREQ : Auto power off enable annunciator RS232 : Communication is activated annunciator : Recording mode annunciator : Maximum reading annunciator : Minimum reading annunciator...

  • Page 4: Specifications

    ® ® SPECIFICATIONS CAPACITANCE: : Hi limits annunciator, Tolerance high annunciator : Lo limits annunciator, Tolerance low annunciator : Indicates the battery power is weakening : Beeper tone indicator for tolerance mode MKΩ : Resistance (O) mhannunciator nd :u Ictance (Henry) annunciator munpF : Capacitance (ara) annunciator...
  • Page 5 ® ® INDUCTANCE:...
  • Page 6 ® ® RESISTANCE:...
  • Page 7 ® ® OPERATION INSTRUCTION Remark Cautions: 1. Q value is the reciprocal of DF. It is recommended that you read the safety and operation instructions 2. The specification is based on the testing sockets (clips) performed before using the meter. on the meter.
  • Page 8 ® ® (1) AUTO POWER-DOWN (4) RANGE BUTTON If unused for about 10 minutes, the meter will power-down Press (RANGE) button to select the Manual Range mode and turn off automatically. Press button switches to resume power-on mode. the “AUTO” annunciator. (The meter remains in the range it was in When the power is down, press button to turn on the meter.
  • Page 9 ® ® 4. OPEN, SHORT calibration: (8) MIN/MAX BUTTON Press “SET”, LCD will display CAL OPEn, and press Press “Min/Max” to enter the Min/Max/Avg mode, and stop the auto PAL/SER(ENTER), the program enters “OPEN” calibration, after shut down function, In Addition to power and hold key, the other keys completing the open.

  • Page 10: Rel Relative Mode

    ® ® 8. Data setting: (11) HI/LO LIMITS (ONLY MAIN DISPLAY) When using the character on the nameplate to input data, the Press “Hi/Lo LIMITS” to enter the Hi/Lo LIMITS mode, and change previous setting will appear, and the place that waits to be entered to manual range mode, the original Hi/LO LIMITS value and will flash.

  • Page 11: Maintenance

    ® ® RS-232 COMMAND TABLE MAINTENANCE Use IR as the interface of Data transmission, and use external computer to WARNING Remove test leads before changing battery or fuse or start RS-232 functions. performing any servicing. RS-232 Interface Parameter: Baud rate: 1200 Battery Replacement Parity check: EVEN Power is supplied by a 9 volt “transistor”...
  • Page 12 ® ® L / C / R Bit. Q / D / R ± A(1KHz) / B(120Hz) P(PAL) / S(SER) A(AUTO) / M(MENU) Start Stop 0 / 1: Main Display MSD, Setting Code Code V alue 8: while changing range , 9: OL Data 6~10: Main Display Data...
  • Page 13 ® ® (3) RS-232 Output Chart for Main Display: Range for Q value , 9 : OL S(SET) / _(normal) F(FUSE) / _(normal) H(HOLD) / _(normal) R(Present value) / M(Maximum value) /I(Minimum value) / X(Max-Min value) / A(Average value) / _(normal) R(REL) / S(REL SET) / _(normal) L(LIMITS) / _(normal) T(TOL) / S(TOL SET) / _(normal)
  • Page 14 ® (4) RS-232 Output Chart for Second Display: Range (Rs=100Ω) (Rs=1KΩ, 10ΚΩ) (Rs=100KΩ) (5) FORMULA: (1+Q [1/(1+D (1+D [1+(1/Q /(1+Q...

Table of Contents