Table of Contents
Advertisement
Quick Links
LIST OF PRODUCTS
Digital Multimeter
Digital AC & AC/DC Clampmeter
AC Clamp Adaptor
AC/DC Current Adaptor
Thermo Anemometer
Thermo Hygrometer
Distance Meter
Digital Lux Meter
Network Cable Tester
Power Factor Regulator
Earth Resistance Tester
Digital Panel Meters
DC Power Supplies
High Voltage Detector
Calibrators
Gas Analysers
Frequency Counter
Function Generator
Phasing Sticks
Battery Tester
Waterproof Pen Testers
Solar Power Meter
EMF Detector
Wood, Paper & Grain Moisture Meter
Transistorised Electronic Analog & Digital Insulation
Resistance Testers(upto 10 KV)
Digital Sound Level Meter & Sound Level Calibrator
Digital contact & Non-contact Type Tachometer
Digital Non-contact (infrared) Thermometer
Maximum Demand Controller/Digital Power Meter
Digital Hand Held Temperature Indicators
G 17, Bharat Industrial Estate, T. J. Road,
Sewree (W), Mumbai - 400 015. INDIA.
Sales Direct : (022) 27754546, 24156638
Tel. : (022) 24124540, 24181649. Fax : (022) 24149659
Email :
sales@kusam-meco.co.in;
Website : www.kusamelectrical.com
®
kusam_meco@vsnl.net
AN ISO 9001:2015 COMPANY
RTD CALIBRATOR
(Source & Sink)
MODEL - KM -CAL 803
OPERATION MANUAL
® ®
Advertisement
Table of Contents
Related Manuals for Kusam-meco KM -CAL 803
Summary of Contents for Kusam-meco KM -CAL 803
- Page 1 Digital Sound Level Meter & Sound Level Calibrator Digital contact & Non-contact Type Tachometer Digital Non-contact (infrared) Thermometer Maximum Demand Controller/Digital Power Meter MODEL - KM -CAL 803 Digital Hand Held Temperature Indicators ® G 17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015.
-
Page 2: Table Of Contents
® ® RTD CALIBRATOR TABLE OF CONTENTS (Source & Sink) TITLE PAGE NO. MODEL - KM -CAL 803 Safety............Components and functions of meter’s ..III. Maintenance........IV. Power On/Power Off The Meter....Output Of The Meter......Measurement........ VII. Setting Functions........ - Page 3 ® ® Section One Safe Use To ensure safe use, the meter and manual employ the following symbols: display Warning : Identifies conditions and actions that may pose hazard (s) to the Range selection user and avoid methods. Power-on Caution : Identifies conditions and actions that may damage the meter or the equipment under test and avoid methods.
-
Page 4: Maintenance
® ® Indicates the graduation no. of thermal resistance(RTD) Section Three Maintenance This section provides some basic maintenance procedures. Repair, Calibration, and servicing not covered in this manual must Be performed by qualified personnel. For maintenance procedures not described in this manual, contact a Service Center. （1）General maintenance ... -
Page 5: Measurement
® ® Current to this meter. For realizing the correct simulateoutput of 400Ω,the incentive Section Six Measurement current should be within ±0.5～±3mA range;for simulate output of 4000Ω,the Warning incentive current should be within ±0.05～±0.3mA range; Usage: the maximum voltage allowed between the terminals and within the Note terminals and the ground is 30V, any exceeding over this voltage may cause damage to the meter and even make injury to persons. -
Page 6: Setting Functions
Fahrenheit degree is the temperature unit; IN P U T Press 〔4/3/2W〕key to store the setting. C O M R T D M A X M A X M A X 3 0 V 3 0 V 3 0 V Section Eight Performance Index ... - Page 7 ® ® Power : Two 1.5V alkaline batteries(LR6) Output function and technical index Power consumption : About 70m/3V Output Resolution Range Output Accuracy Illustration Maximum allowed voltage : 30V（within terminals or between Function Range terminal and earth ground） Measurement current: about 1mAOpen circuit voltage: Operation temperature range : 0°C～50°C about 2.5VThe accuracy...
-
Page 8: Test Certificate
WARRANTY MUMBAI TEST CERTIFICATE Each “KUSAM-MECO” product is warranted to be free from defects in material and workmanship under normal use & service. The warranty period is one year (12 months) and begins from the date of despatch of RTD CALIBRATOR goods.
Need help?
Do you have a question about the KM -CAL 803 and is the answer not in the manual?
Questions and answers