Usb Connection; Usb Disk Connection; First Time Installation - Bush FVPZAPPER100 Instruction Manual

Connections
Bringing it all together

USB Connection

You can connect a USB hard disk drive or USB memory
stick to your box by using the USB input. This feature
allows you to play files stored in a USB drive or record
programmes.
2.5" and 3.5" inch (hdd with external power supply)
external hard disk drives are supported.
To record a programme, you should first connect a USB
disk to your box while the it is switched off. You should
then switch on the box to enable recording feature.
Otherwise, recording feature will not be available.
IMPORTANT !
Note that ALL the data stored on the USB disk will be lost
and then the disk format will be converted to FAT32/NTFS
in such a case.
It is possible that certain types of USB devices (e.g. MP3
Players) or USB hard disk drives/memory sticks may not
be compatible with this device.
The device may not support all disk formats. If you
connect a USB disk with an unsupported format, then
you will be asked to format the content. See the section,
"Format Disk" in the following pages for more information
on disk formatting. Note that ALL the data stored on the
USB disk will be lost and then the disk format will be
converted to FAT32/ NTFS in such a case.

USB Disk Connection

• Plug your USB device to the USB input of the box.
Notes:
Plug or unplug your USB disk while the box is switched off.
If you are going to connect a USB hard disk drive to the
box, USB connection cable used between the disk drive
and the box should have a USB logo and should be as
short as possible.
While formatting a USB hard disk that has 1TB (Tera Byte)
or more file capacity, you can experience problems with
the formatting process. In such a case, you should format
the disk with your personal computer and the formatted
disk type is recommended as FAT32. The box supports
NTFS and FAT32 formats.
CAUTION !
Quickly plugging and unplugging USB devices, is a very
hazardous operation. Especially, do not repeatedly quickly
plug and unplug the drive. This may cause physical
damage to the USB player and especially the USB device
itself.
Do not pull out USB module while playing or recording
a file.
If you require any technical guidance or find that your set-top box is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
16 Connections

First Time Installation

When turned on for the first time, the language selection
screen is displayed. Select the desired language and
press OK.
On the next screen, set your preferences using the
directional buttons.
Note: Depending on the Country selection you may be
asked to set and confirm a PIN at this point. The selected
PIN cannot be 0000. You have to enter it if you are asked
to enter a PIN for any menu operation later.
About Selecting Broadcast Type
Terrestrial Search: If Terrestrial Search broadcast search
option is turned on, the box will search for digital terrestrial
broadcasts after other initial settings are completed.
Press OK button on the remote control to continue and
the Network/Internet Settings menu will be displayed,
if you confirm the previously displayed message asking
whether you want to do the network settings. Please refer
to Connectivity section to configure a wired connection.
After the settings are completed press OK button to
continue. To skip to the next step without doing anything
select No and press the OK button when the message
is displayed asking whether you want to do the network
settings.
On the next screen you need to agree to the terms and
conditions of Freeview Play to make use of the related
services. Scroll the page to read the entire text using the
up/down directional buttons or Programme +/- buttons.
Highlight Yes and press OK on the remote to confirm and
proceed. Highlight No and press OK to proceed without
confirmation.
After the initial settings are completed set-top box will
start to search for available broadcasts.
After all the available stations are stored, scan results will
be displayed. Press OK to continue. The Edit Channel List
menu will be displayed next. You can edit the channel
list according to your preferences or press the Menu
button to quit.
While the search continues a message may appear, asking
whether you want to sort channels according to the
LCN(*). Select Yes and press OK to confirm.
(*) LCN is the Logical Channel Number system that
organizes available broadcasts in accordance with a
recognizable channel number sequence (if available).
Note: Do not turn off the box while initializing first time
installation. Note that, some options may not be available
depending on the country selection.