Table of Contents
Advertisement
Quick Links
Thank you for trusting Prestige products! If you are a consumer, please note:
Professional installation is strongly recommended.
This manual assumes the installer has adequate knowledge of the following expertise. Therefore, it does not
cover these topics in detail:
•
12-volt electronics
•
Testing and verifying circuits
•
Making safe and lasting wiring connections
•
Factory ignition, power, lighting, data bus and sensing systems
•
Factory systems and components to avoid
•
Safe wire routing, circuit protection and product placement
•
Access to vehicle-specific technical information
In addition, this manual assumes the installer has the proper tools, skill and facilities to perform a professional installation.
Performing an improper installation could result in damage to the vehicle or its components, improper system function,
unsafe vehicle operation or physical injury. Such instances would not be covered by the vehicle manufacturer's warranty,
nor by Voxx Electronics, Inc.
Detailed Descriptions
2
Wire Harness Colors and Functions
2
Main Harness
4
Internal Components
4
Shock Sensor
4
Tilt Sensor
5
Setup Options
5
Remote Programming
5
Security Control
8
System Operation
8
Alarm Override Procedures
9
Anti Hi-Jacking
2019 Voxx Electronics Corporation. All rights reserved.
APSPS1
Power Sports Security System
Installation and Reference Guide
Quick Reference
10
System Operation
10
Remote Operation
10
System Programming
10
Programming Mode Entry / Exit
11
Feature Bank Options
11
System Diagnostics
11
Troubleshooting Trigger Zones
11
Adjusting Shock Sensor
12
Wiring Diagrams
12
Full System Connections
APSPS1_RevA_1/19
Advertisement
Table of Contents
Related Manuals for Voxx Electronics Prestige APSPS1
Summary of Contents for Voxx Electronics Prestige APSPS1
- Page 1 Programming Mode Entry / Exit Tilt Sensor Feature Bank Options Setup Options System Diagnostics Remote Programming Troubleshooting Trigger Zones Security Control Adjusting Shock Sensor System Operation Wiring Diagrams Alarm Override Procedures Full System Connections Anti Hi-Jacking 2019 Voxx Electronics Corporation. All rights reserved. APSPS1_RevA_1/19...
-
Page 2: Main Harness
Detailed Descriptions: Wire Harness Colors and Functions Main Harness See page 12 for the full system diagram. 1. RED – 12-Volt Input (+) The RED wire connects to the vehicle’s primary 12-Volt (+) wire to power the system. Verification: The power wire registers 12-Volt (+) at all times. Note: Before making this connection, remove all module fuses until the system is completely connected. - Page 3 Detailed Descriptions: Wire Harness Colors and Functions Main Harness See page 12 for the full system diagram. 9. PURPLE/WHITE – Loop Trigger Input (-) The PURPLE/WHITE wire is used as a Loop Alarm Trigger. If the loop is closed (Connected) when the alarm is armed, the alarm will trigger if the loop is opened (Disconnected).
-
Page 4: Shock Sensor
Detailed Descriptions: Internal Components Shock Sensor The shock sensor is integrated onto the module circuit board. The module should be securely attached to a vehicle surface or sturdy wire harness. Testing takes place after all connections are made and the system is powered up. Refer to Quick Reference: System Diagnostics on page 11 for instructions on testing and adjusting the shock sensor. - Page 5 Detailed Descriptions: Setup Options Bank 1: Add / Remove Remote Controls Remote control programming is located in Feature Bank 1. This system will Auto Program all remote functions. To Auto Program a remote control: 1. Cycle the ignition key to ON 5x, Ending in ON. 2.
- Page 6 Detailed Descriptions: Setup Options Security Control (Bank 2) (cont.) See page 10 for Programming Instruction. Feature 3: Tilt Sensor Adjustment Function: Set the sensitivity of the internal tilt sensor. Setting Choices: • Option 1 - Alarm will trigger with a 1° change in angle. •...
- Page 7 Detailed Descriptions: Setup Options Security Control (Bank 2) (cont.) See page 10 for Programming Instruction. Feature 8: AUX Ch. 3 Output Timing Function: Set the output timing of the DARK BLUE Aux Ch. 3 Output • Option 1 - Output pulses for 1 Second. •...
- Page 8 Detailed Descriptions: Alarm Override Procedures Default Alarm Override The Default Alarm Override procedure will disable the alarm when the remote control is not available or has become inoperative. If the vehicle door is opened without disarming, the alarm will sound and the vehicle will not start when attempting to start with the key.
- Page 9 Detailed Descriptions: Anti Hi-Jacking Anti Hi-Jacking Anti Hi-Jacking is a feature that will activate the alarm and disable the engine starter if the vehicle is stolen. This feature must be activated in the Feature Bank 2, Feature 2. Once activated in Feature Bank 2, this feature must also be activated by the user.
-
Page 10: Remote Control Operation
Quick Reference: System Operation and Programming Remote Control Operation This system is only compatible with the Prestige two (2) button 1-Way remote controls. The matrix below describes how the remote control will operate the basic system functions. See Owner's Guide for more detailed information Bu�on Ac�on Func�on... -
Page 11: Adjusting The Shock Sensor
Quick Reference: System Programming & Diagnostics Bank 1: Add / Remove Remote Controls Remote control programming is located in Feature Bank 1. This system will Auto Program all remote control functions. To Auto Program a remote control: 1. Cycle the ignition key to ON 5x, Ending in ON. 2. - Page 12 Quick Reference: Wiring Diagrams APSPS1_RevA_1/19...