Table of Contents
Advertisement
5
USER
Your Easi-Flo le water heater incorporates the very latest gas water
heating technology, and if cared for, will give years of reliable use and
efficiency.
Please therefore take some time to read these instructions carefully.
b
When the product reaches the end of its life it should not be
disposed of as solid urban waste but should be brought to a
separated waste collection facility.
5.1 Do's and don't's
- Do ensure that you know how to isolate the appliance in an emer-
gency
- Do ensure that you are familiar with the appliance controls
- Do ensure that your installer has completed the appliance log book
- Do not attempt to remove the appliance casing or gain internal ac-
cess
- Do not hang clothes etc. over the appliance
- Do not forget to have the appliance serviced annually
5.2 Guarantee registration card
Please take the time to fill out your guarantee registration card. The
completed warranty card should be posted within 30 days of installa-
tion.
5.3 Benchmark log book
The Benchmark Log Book is supplied with your appliance. This im-
portant document must be completed during the installation/commis-
sioning of your appliance. All Gas-Safe Registered Installers carry a
Gas-Safe ID card, and have a registration number. Both should be
recorded in your Benchmark Log Book. You can check your installer
by visiting the Gas-Safe website. Failure to install and commission the
appliance in accordance with the manufacturers instructions may in-
validate the warranty. This does not affect your statutory rights .
5.4 How does it work?
Your Easi-Flo water heater is an instantaneous gas water heater that
operates to produce hot water whenever a hot water outlet (tap) is
opened. The Easi-Flo will operate whenever a flow of water, through
the appliance is sensed. The Easi-Flo lights electronically and does
not have a pilot light. In the unlikely event of a fault developing with
your appliance, the supply of gas to the burner will be terminated au-
tomatically.
5.5 Diagnostic fault indicator
In the unlikely event of a fault developing, the Easi-Flo displays a
unique fault indicator that helps identify where the fault lies.
5.6 Control panel
A
B
ON - OFF/RESET key
A
B
MENU - CONFIRM key
+ key
C
- key
D
ON - OFF/RESET key
Allows the appliance to switch on and off. It also allows it to be reset in
the event of a fault.
MENU
Allows the selections to be confirmed, to enter the user menu and, if
pressed for more than two seconds, to access the technical menu (in
this case you will be asked to enter the password).
+ and - keys
They allow you to navigate the various functions that are available, to
change the value of a parameter and to change the temperature that
has been set for the domestic hot water.
5.7 Description of icons
Temperature adjustment lockout
Bottle feeder function
Function for choosing temperature unit of measurement
General alarm
Domestic hot water pick-up
Flame presence
Flame lockout
Enter the technical menu
Flue gases fault
5.8 Selecting functions
Press the MENU (B) key.
Using the "+" e "-" keys it is possible to scroll through the available
functions on the display. The icon regarding the selection made, blinks
together with the central segments.
In the case of the wrench (
Pressing the MENU (B) key you pass to value setting mode. Either
"on" or "oF" is displayed depending on the function that is currently
active or inactive. To change the status of the function:
- press the "+" and "-" keys
- press the MENU (B) key to confirm and return to the selection
of the functions.
b
Keeping either the "+" or "-" key pressed, the fast scrolling mode
is activated.
Button lock function
Allows the keyboard to be locked out. It is activated or deactivated
through a combination of the keys ("+" and "-" keys pressed together
for 5 seconds).
When the mode is active (lockout) it is not possible to use the keybo-
ard.
Feeder bottle function
Selecting this function makes it possible to set the maximum tempera-
ture at which the water is delivered (maximum 65°C; minimum 36°C).
If the function is not active,"oF " appears on the display. If the function
is active, the "bottle feeder" temperature that was previously set is
displayed.
The maximum value that can be set is established in parameter 11
(see table of parameters).
To change the set value press the MENU (B) key and with the "+" or "
C
-" key select the desired value.
D
B
Then confirm the selection by pressing MENU (B) again.
14
) the central segments do not appear.
Hide quick links:
Advertisement
Table of Contents
