Contact Points; Timing Light Connected To Magneto And Breakers; Propeller Blade Minor Repair; Engine Control Console - Piper Pawnee Brave Service Manual

PAWNEE BRAVE SERVICE MANUAL
LIST OF ILLUSTRATIONS
(cont)
Figure
8A-9.
8A-10.
8A-11.
8A-12.
8A-13.
8A-14.
8A-15.
8A-16.
8A-17.
8A-18.
8A-19.
8A-20.
8A-21.
8A-22.
8A-23.
8A-24.
8A-25.
8A-26.
8A-27.
8A-28.
8A-29.
.8A-30.
8B-I.
8B-2.
8B-3.
8B-4.
8B-5.
8B-6.
8B-7.
8B-8.
8B-9.
8B-10.
8B-11.
8B-12.
8B-13.
8B-14.
8B-15.
8B-16.
8B-17.
8B-18.
8B-19.
8B-19A.
8B-20.
8B-21
8B-22.
8B-23.
8B-24.
8B-25.
8B-26.
8B-27.
8B-28.
Revised:
Fuel-Air Bleed Nozzle ......................................................
Contact Points ............................................................
Rotor Holding Tool Installed ...............................................
Timing Kit Installed .......................................................
Aligning Timing Marks ....................................................
Checking Flyweight Clearance of Impulse Coupling ............................
Engine Timing Marks ......................................................
Magneto Timing Marks ...................
.................................
Removing Spring From Lead Assembly ......................................
Assembly Tool ............................................................
Using Assembly Tool ......................................................
Measuring Lead Assembly Length ...........................................
Cutting Metallic Braid From End of Lead ....................................
Unbraiding Metallic Shielding ...............................................
Forming Shielding Around Ferrule ..........................................
Ferrule Seating Tool.......................................................
Needle ...................................................................
Measuring Wire From Top of Ferrule ........................................
Installing Grommet Over Lead Assemblies ....................................
Lead Assembly Installed in Grommet ........................................
Wire Doubled Over For Installation of Eyelet .................................
Removing Spark Plug Frozen to Bushing .....................................
Engine Cowling Installation .................................................
Propeller Installation (PA-36-375) ...........................................
Propeller Blade Minor Repair ...............................................
Propeller Governor ........................................................
Engine Installation (Lycoming) ..............................................
Engine Control Console ....................................................
Schematic Diagram of RSA Fuel Injector System..............................
Fuel Injector .............................................................
Fuel Air Bleed Nozzle ......................................................
Height of Spring in Distributor Block Tower..................................
Contact Points ............................................................
Engine Timing Marks......................................................
Timing Marks on Magneto Rotor ...........................................
Painted Tooth Centered in Timing Window ...................................
Can End View of Magneto ..................................................
Timing Mark on Rotor Aligned with Pointer (Right Hand Rotation).............
Timing Light Connected to Magneto .........................................
Timing Light Connected to Magneto and Breakers.............................
Check Harness Lead Continuity .............................................
Testing Insulation Resistance of Harness Lead .................................
Removing Spring From Lead Assembly ......................................
Assembly Tool ............................................................
Using Assembly Tool ......................................................
Measuring Lead Assembly Length ...........................................
Cutting Metallic Braid From End of Lead ....................................
Unbraiding Metallic Shielding ...............................................
Forming Shielding Around Ferrule ..........................................
Ferrule Seating Tool .......................................................
Needle .................................................
Aerofiche
Grid No.
IK23
IK24
IL3
IL3
1L4
IL4
IL5
IL5
IL7
IL8
IL8
IL8
IL9
IL9
ILIO
IL0
IL10
ILII
ILII
I L 11
ILII
ILII
IL13
2A12
2A13
2A15
2A17
2A21
2A22
2BI
2B2
2B4
2B4
2B4
2B5
2B7
2B7
2B8
2B9
2B9
2B9
2B9
2B14
2B15
2B16
2B16
2B16
2B17
2B17
2B18
2B18
2B18
7/20/81
1A7