Caleg WOWMAKER M 130 General Operating Instructions

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

General Operating Instructions

M130.2.1EN

Table of Contents

Summary of Contents for Caleg WOWMAKER M 130

Page 1 General Operating Instructions M130.2.1EN...
Page 2: Table Of Contents
Zum Gerlen 1 You can also find an overview at www.wowmaker.de/release. D - 66131 Saarbrücken Subject to technical changes. Phone +49 6893 89 470 Mail your@wowmaker.de Static calculation from June 15, 2018, SuS-Ingenieure GmbH, Ettlingen Internet www.wowmaker.de © 06.2018 caleg Schrank und Gehäusebau GmbH...
Page 3: Quick Start Guide
I. Quick Start Guide The Quick Start Guide is a condensed version of the user guide for experienced users. It does not replace the user guide. Check the transport dimensions, floor load and fuses at the installation location.. 4 See page 21 4 See drawing page 24 The Flightcase has four inner and four outer wheels.
Page 4: Introduction And Important Terms
II. Introduction and Important Terms The WOWMAKER M130 (hereinafter referred to as WOWMAKER) is an easy-to-use plug and play solution for the SAMSUNG IF 1.5 system. It combines a mobile LED Full HD display with a lift and transport system. It consists of 3 main components, which together make up the WOWMAKER: 1.
Page 5: Flightcase
ATTENTION: During transport, make sure that the flightcase is not tilted sideways by more than 9 degrees. III. Flightcase The Flightcase is designed to fit through a door with a width of 85cm and a standard height of 200cm. Due to its dimensions and weight (~750kg including Studiolifter and Studioframe) at least 2 people are required to move the WOWMAKER.
Page 6: Studiolifter
IV. Studiolifter The Studiolifter is controlled by a wired remote control. Optionally, a permanently connected control unit with digital height display can also be purchased for the device. The motors in the lifting columns are not intended for constant changes in the height position of the display. The motion sequence should not exceed 4 minutes.
Page 7: Studioframe
V. Studioframe The Studioframe consists of 18 single modules (three lines of six modules each) and one S-Box (UHD video processor). The modules have FULL FRONT service access. Do not touch the LED front with objects or dirty hands. This can irreparably damage the front boards. Display wiring (marked red) (marked blue)
Page 8: Transport
VI. Transport ATTENTION: The Flightcase has four inner and four outer wheels. The inner wheels must always have contact with the ground. When transported on a tail lift, the four outer wheels can overhang.
Page 9: Set-Up
VII. Set-Up Move the WOWMAKER to its intended position. This must be flat and able to support ~ 750kg, which corres- ponds to a floor load of ~ 600kg/m². ATTENTION: During transport, make sure that the Flightcase is not tilted sideways by more than 9 de- grees.
Page 10 STEP 3: Open the back door of the Studiolifter. Insert the cable end with the Neutrik plug from the outside in through the brush strip and connect it to the socket strip. Lock in place with a 1/8 turn and insert the wired remote control from the inside out. Close the door again (does not have to be locked).
Page 11 STEP 4: Connect the Neutrik power cable to the power supply (observe safety instructions on page 10). STEP 5: Lower the foot with the button and lift the Studioframe up a bit. Because the foot is retracted in transport mode, the lift function must be operated upwards to lower it. ATTENTION: Risk of crushing by the foot plate when lowering the foot! ATTENTION: The lower edge of the Studioframe must be higher than the upper edge of the “spare box”!
Page 12 STEP 6: Pull the rear slide-in panel at the bottom of the Flightcase upwards. Now the floor of the case can be rolled away to the front. Place the front and rear case back on the case floor. Make sure you close them with the butterfly locks. Slide-in panel...
Page 13: Starting The Led Display
VIII. Starting the LED Display (Studioframe) STEP 1: Set up the WOWMAKER in accordance with Chapter VII “Set-Up” and ensure that it is connected to a power supply. “NO VIDEO” will appear on the display. STEP 2: Turn on the S-Box with the remote control. STEP 3: Connect the video signal to the S-Box.
Page 14 If the S-Box is operated separately, all cables must be routed through the brush strip to the inside. The S-Box power supply unit can be detached from the mounting plate (attached with Velcro). Infrared Extender The Infrared (IR) Extender allows you to use the WOWMAKER's IR remote control from any angle, e.g. from the front.
Page 15: Dismantling The Wowmaker
IX. Dismantling the WOWMAKER Disconnect the signal cable. Roll the floor frame of the Flightcase to the front of the Studioframe and its lifting columns. The recesses in the floor frame should surround the lifting columns. Replace the rear slide- in panel.
Page 16 Brakes released ATTENTION: You must lock the brakes on the castor wheels if you do not want the WOWMAKER to be moved. Brakes locked...
Page 17: Care And Maintenance
X. Care Remove dust and dirt from the Flightcase and Studiolifter regularly. FLIGHTCASE: Clean using pure water with the aid of a soft, non-abrasive cloth or rag. If necessary, add a small amount of neutral cleaning agent (pH 7) to the water. STUDIOLIFTER: Clean using pure water with the aid of a soft, non-abrasive cloth or rag.
Page 18: Important Information
XI. Important Information Operate device indoors only! Observe the load limits of the tail lift! The Flightcase has four inner and four outer wheels (in some models with an additional middle wheel). The inner wheels must always be in contact with the ground. When transported on a tail lift, the outer four wheels can therefore overhang.
Page 19: Troubleshooting
XII. Troubleshooting Problem Possible solution Flightcase won't close Place groove and rails flush on each other. The rear slide-in panel must be inserted before lowering! 4 See page 12 Flightcase cannot be locked Check that the two cases are positioned correctly. The rear case (the wider one) covers the rear part and the front case covers the display side of the WOWMAKER.
Page 20 The position of the Lifter cannot be Check power supply.. changed 4 See above: "WOWMAKER has no power" 4 Call caleg service: +49 6893 89 470 Columns do not run parallel or To do this, you must press the DOWN button on the remote out of sync control (approx.
Page 21: Features And Specifications
WOWMAKER M 130 Description Complete mobile 130 zoll LED full-HD system with Lifter and Flightcase Display technology Samsung, Series IF1.5 Cover, Lifter, Flightcase caleg Schrank und Gehäusebau GmbH Display size 2895mm x 1635mm Display diagonal 3300mm (130 zoll) Active display area...
Page 22 IF SERIES – IF015H Physical Parameter Pixel pitch 1.5mm Pixel density 444,444m² / 41,290ft² Diode type Surface Mount Device (SMD) Optical Parameter Max brightness (after calibration) 800nit; Dynamic Peak 1.600nit Contrast ratio 5,000:1 Viewing angle – horizontal 160° Viewing angle – vertical 160°...
Page 23 S-BOX – SNOWJ3U / Basic Model Code SBB-SNOWJ3U/** Feature Resolution UHD (3840 X 2160) S/W platform Tizen 2.4 Log function Supported Image quality enhancing HDR, Dynamic Peaking Diagnostics Supported Ethernet Supported Input signal DP 1.4, HDMI 2.0 port x 2, USB Output signal DP, HDBT MagicInfo solution...
Page 24 Drawings 841 Transport dimensions 3019 Transport dimensions Slide-in panel Installation site & route to installation site Total weight (with Flightcase): 750kg Floor load: 600kg/m² Transport dimensions (with Flightcase): 1970 mm x 3020 mm x 841mm (HxWxD) Required loading equipment: Loadable with 7.5t truck with tail lift Clear dimensions for transport: Door opening size 2000mm x 850mm (HxW), maneuvering clearance after door: 3300mm...
Page 25: Cabling And Wiring
XIV. Cabling and Wiring S-Box connection with power supply unit Network cable between S-Box and display Neutrik plugs from the Display Neutrik power cable power cable for Lifter control S-Box power supply unit Check that all connections are plugged in and locked. Connections to the socket strip: Connections S-Box: •...
Page 26 Service contacts SAMSUNG S-Box, LED display Software Phone (D) 0800 58 95 347, Mail dssc@samsung.com Hardware and repairs Phone +49 (0)3591 27 220, Mail samsung-led@letmerepair.com Studiolifter and Flightcase caleg Schrank und Gehäusebau GmbH Phone +49 6893 89 470, Mail your@wowmaker.de Notizen...