KX-TDE600GR 1 Safety Precautions 1.1. For Service Technicians • Repair service shall be provided in accordance with repair technology information such as service manual so as to prevent fires, injury or electric shock, which can be caused by improper repair work.
KX-TDE600GR 2.4. About Lead Free Solder (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con- tains lead. We will use PbF when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).
KX-TDE600GR 3 Specifications 3.1. General Description Control Bus Original bus (16 bit, 8 MHz,10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slot) Switching Distributed Switching Power Input PSU-M 100 V AC to 130 V AC; 2.5 A/200 V AC to 240 V AC; 1.4 A; 50 Hz/60 Hz PSU-L 100 V AC to 130 V AC;...
KX-TDE600GR 4.2.2. Description of Each Part LED Lamp (BATT ALARM): Turns on to indicate the dropping of the lithium battery voltage (less than 2.8V). LED Lamp (SD ACCESS): Turns on when the SD card is accessing. SD card slot: Mounts the system program SD card.
KX-TDE600GR 4.2.3. Circuit Description 4.2.3.1. Outline of Block Description • CPU2 block (BLOCK1) This block operates the main unit control. Besides this operates various controls, select signal generation, DMA control and serial port control. This contains the built-in clock function.
Page 14
KX-TDE600GR • NEXUS ( + SRAM ) block (BLOCK 8) This provides the communication function between each option card, call control (TSW function), conference call, tone genera- tion and gain control function. Configuration: IC1303(ASIC(NEXUS)), IC1302, X1301,IC1301(SRAM) , CN1301(RMT card connector) and so on.
Page 15
KX-TDE600GR • POWER block (BLOCK 13) This consists of DC/DC converter circuit and various regulators. Configuration: IC1901 ( 3.3V, 2.5V DC/DC converter ), IC1902 ( 1.25 DC/DC converter ), IC1908 (1.8V regulator), IC1907 (1.2V regulator), IC1903 (Comparator), Q1901, Q1902, Q1903 (FET, transistor), B1901, IP1901 (circuit protection device) and so on.
KX-TDE600GR Back Board Circuit Operation 4.3. The back board (BB) connects signals between all cards in KX-TDE600. It also supplies power from the power supply unit to the cards. CONNECTORS EXPLANATION (1) Power Supply Unit Connector: CN100 (2) Free Slot Connectors: CN101-CN110...
KX-TDE600GR 4.4. Outline 4.4.1. General Description The control system of this unit is composed of the main control section (IPCEMPR) controlling the entire system, exchanging voice data, the circuit control section (LPR) controlling various telephone lines and the power supply section (POWER).
KX-TDE600GR 4.4.5. System Control 4.4.5.1. System Control Block Diagram...
Page 19
KX-TDE600GR 4.4.5.2. Voice (TDM Highway) Bus Block Diagram...
Page 20
KX-TDE600GR 4.4.5.3. Voice Bus Logical Assignment In the line card, the CT_D line number, which is output in accordance with the inserted slot, and the time slot are assigned on a software base. For the detail of output slot for each card, refer to the service manual of card.
KX-TDE600GR 6 Installation Instructions 6.1. System Construction 6.1.1. Basic System Basic Shelf The Basic Shelf contains an IPCEMPR card for controlling the PBX. To use the basic system, install a power supply unit (PSU) in the PSU Slot and optional service cards in Free Slots. To expand to a multiple-shelf system, you also need to install a BUS-M card in the BUS-M Card Slot.
Page 26
KX-TDE600GR 2-shelf System Expanded system (Basic Shelf + 1 Expansion Shelf). Expansion Shelf 1 is mounted on the Basic Shelf. CAUTION If you are installing a 2-shelf system in an area prone to earthquakes, make sure to fix the system to the wall using the wall brackets (supplied with an optional Mounting Kit).
Page 27
KX-TDE600GR 4-shelf System (Tower Type) Fully expanded system (Basic Shelf + 3 Expansion Shelves). Expansion Shelves 1 to 3 are mounted on the Basic Shelf. A Mounting Kit is required for the 4-shelf system.
Page 28
KX-TDE600GR 4-shelf System (Side-by-side Type) When vertical space is limited, it is possible to install a fully expanded system (Basic Shelf + Expansion Shelf 1, and Expansion Shelf 2 + Expansion Shelf 3 ) in a side-by-side configuration. Expansion Shelf 1 is mounted on the Basic Shelf, and Expansion Shelf 3 is mounted on Expansion Shelf 2.
KX-A258X Blank Slot Cover KX-T7765X Doorphone Equipment Compatibility Compatible Panasonic Proprietary Telephones The PBX supports the following telephones: • IP proprietary telephones (e.g., KX-NT300 series) • IP softphones (e.g., KX-TDA0350) • Digital proprietary telephones (e.g., KX-DT300 series) • Analog proprietary telephones (e.g., KX-T7700 series) •...
Page 33
KX-TDE600GR Notice • This PBX supports SIP Extensions. However, some PBX features may not be available for SIP Extensions, depending on your telephone type. • Under power failure conditions, the connected telephones may not operate. Please ensure that a separate telephone, not depen- dent on local power, is available for emergency use.
KX-TDE600GR 6.2.4. System Capacity Type and Maximum Number of Slots The PBX supports the following type and number of slots. Slot Type Maximum Number Basic System 2-shelf System 3-shelf System 4-shelf System IPCEMPR Card Slot BUS-M Card Slot Free Slot...
Page 35
KX-TDE600GR Cards Installed in Free Slots or Virtual Slots Card Type Maximum Number Basic System 2-shelf System 3-shelf System 4-shelf System IPCEMPR CO Line Card 14*1 24*1 34*1 40*1 Virtual CO Line Card V-IPGW16 V-SIPGW16 Physical CO Line Card 10*1...
Page 36
KX-TDE600GR Maximum CO Lines and Extensions Type Basic System 2-shelf System 3-shelf System 4-shelf System Total Number of CO Lines CO Line (Physical CO Line Card) CO Line (Virtual CO Line Card) 1008 1152 Total Number of Extensions Extension (Physical Extension Card)
Page 37
KX-TDE600GR Power Supply Unit Selection for Each Shelf The PBX needs a power supply unit (PSU) suitable for its configuration. For each shelf, calculate the load figure from the type and number of items of equipment to be connected, and then determine the type of PSU that will be required.
KX-TDE600GR 7 Test Mode 7.1. Utility 7.1.1. Utility-Diagnosis Performs diagnostic tests on cards installed in the PBX, to identify the source of problems. There are 2 types of test, Card Test and Pair Port Test. If any of the tests listed here returns the result "NG" ("No Good"), contact your dealer. Test results can be saved as a TXT-format (text) file.
Page 39
KX-TDE600GR 7.1.1.2. Pair Port Test Tests the combination of an extension port and trunk port to ensure that communication with the trunk port can be carried out successfully. The pair port test can be carried out using one LCOT card and one DHLC, SLC8, SLC16 or MSLC16 card.
Page 40
KX-TDE600GR LPR Program Name on SD Memory Card Corresponding Card PCSINF CSIF PDHLC DHLC8/DLC8/DLC16 PSLC SLC8 PIPGW IP-GW4 (KX-TDA0480) PIPGWH IP-GW4 (KX-TDA0484) PIPGW16 IP-GW16 PPRI23 PRI23 POPB3 PIPEXT IP-EXT16 PVOIPEX IP-EXT16 CS Program Name on SD Memory Card Corresponding Card PCS24G CS using a CSIF card for 2.4 GHz Portable Station...
Page 42
KX-TDE600GR 7.1.1.5. Utility-SD Card File View and Load Displays a list of files on the SD memory card, and allows you to update the programs stored in LPR cards (cards with local pro- cessors) and Cell Stations (CSs). This option is only available at Installer level.
Page 43
KX-TDE600GR 7.1.1.7. Utility-Message File Transfer PC to PBX Transfers Outgoing Message (OGM) files from the PC to the selected MSG card. This option is only available at Installer level, and requires that at least 1 MSG card is installed. The OPB card that it is mounted on must be set to OUS status.
Page 44
KX-TDE600GR 7.1.1.9. Utility-Error Log Collects and displays system error information. Whenever there is a system failure, the PBX stores the error code generated. The connected PC collects all of these codes, along with other information, and displays an explanatory error message.
Page 45
KX-TDE600GR 7.1.1.10. Utility-T1 Signaling Bit Monitor Displays reference signaling bit information for all channels of the T1 card, by monitoring sent and received A, B, C and D bits. This utility is intended for use by dealers. This option is only available at Installer level, and requires that the target T1 card be set to INS status.
Page 46
KX-TDE600GR 7.1.1.13. Utility-Digital Trunk Error Report Displays accumulated information on various types of errors occurring on digital CO lines. This option is only available at Installer level. The value displayed for each error item is the number of times that each error occurred during the time period selected. Average values for these items vary depending upon many factors, such as the equipment being used, and the distance from the tele- phone company.
Page 47
KX-TDE600GR 7.1.1.15. Utility-CS Information Displays information stored by the PBX regarding each Cell Station (CS). This option is only available at Installer level, and requires that the target CSIF, DHLC or DLC card be set to INS status. The displayed items are as follows:...
Page 48
KX-TDE600GR 7.1.1.17. Utility-Ping Performs a connection test on network devices. This function sends echo requests to a particular IP address across an IP net- work, and displays the result of responses and round-trip time. This option is only available when the KX-TDE Maintenance Console is in Interactive mode.
Page 49
KX-TDE600GR 7.1.1.19. Utility-Refresh Activation Key Allows you to enable the activation keys (except for the Activation Key for Software Upgrade to Enhanced Version) without resetting the PBX. This utility recounts the number of available activation keys, and refreshes the system data accordingly. To enable the activation keys, it is necessary to change the card status of all virtual cards to OUS, then back to INS.
KX-TDE600GR 8 Troubleshooting Guide If all the option cards are not started up • Preinstall memory card or IPCMEC card failure. • Check the error log for the maintenance console (Error Code 041). • Replacement of the memory card. 8.1.
Page 54
KX-TDE600GR 8.1.1.1. Main alarm light turns on...
Page 55
KX-TDE600GR 8.1.1.2. SD card access light does not flash...
Page 56
KX-TDE600GR 8.1.1.3. The battery alarm indication light turns on 8.1.1.4. Main power indication light flashes 8.1.1.5. Main alarm indication light flashes...
KX-TDE600GR 10 Disassembly and Assembly Instructions 10.1. IPCEMPR Card 1. Remove the Lid by sliding it in the direction of the arrow 1. 2. This will be removed if the user attaches the Pad Lock as shown in a Fig.1.
KX-TDE600GR 10.2. Back Board 1. Remove four Screws (A). 2. Remove the Left Side Cover and the Right Side Cover. 3. Remove the Hook. And remove the Top Cover. 4. Remove nine Screws (B). 5. Remove the Back Cover.
Page 76
KX-TDE600GR 6. Remove the RS-232C Connector and LED Connector from the Back Board 1. 7. Remove eight Screws (C). 8. Remove the Back Board 1. 9. Remove the LED Connector from the Back Board 2. 10. Remove the Screw (C).
KX-TDE600GR 11 Miscellaneous 11.1. How To Replace a Flat Package IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a sol- dering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TDE600GR 14 Appendix Information of Schematic Diagram Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 1. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
Page 135
KX-TDE600GR Pin No. Pin Name Function Address bus Data bus Data bus Data bus AD10 Data bus AD11 Data bus AD12 Data bus AD13 Data bus AD14 Data bus AD15 Data bus AD16 Data bus AD17 Data bus AD18 RD#/FRAME#...
KX-TDE600GR 15.4. Replacement Parts List Note: Safety Ref. Part No. Part Name & Description Remarks 1. RTL (Retention Time Limited) PSKV1015V1 COVER, TOP PC+ABS( The "RTL" marking indicates that its Retention Time is Limited. PSKV1016X1 COVER, SIDE (R) ABS(5V) When production is discontinued, this item will continue to...