Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Billion BiPAC 2070 (P)
Summary of Contents for Billion BiPAC 2070 (P)
- Page 1 BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge User Manual...
-
Page 2: Safety Warnings
Safety Warnings Do not use the adapter in high humidity or high temperatures. Do not open or repair the case yourself. Avoid using this product and all accessories outdoors. Place the adapter on a stable surface. Only “HomePlug AV” compliant Powerline Communication (PLC) adapter for remote access is necessary. -
Page 3: The Connectors
The Connectors *Reset Button: Hold down the reset button for 1~3 seconds to reset device to factory default *Push Button: Power line sync *Connect your device to a LAN port, using the included Ethernet cable *Connect DC power cord to your DC port on device (for BiPAC 2070P) Connect the AC power... -
Page 4: Push Button Usage
Push Button usage There are 3 types of trigger states for the Push Button. “Broadcast State”, for a 2070(P) providing information for another 2070(P) to join its powerline network group (it works even if it is the only one currently in the group). - Page 5 have device A joining the network group “BC”. Scenario 3: 2070(P) Device A of network group “AD” wants to join an existing network group “BC”. For a device which already belongs to an existing group, if it wants to join another group that device must go into the “Ungroup State”...
- Page 6 Introduction HomePlug AV Adapter with power supplier • Physical layer data rate up to 200Mbps over existing Powerline • Uses powerline technology that takes advantage of the unused bandwidth of the electrical wiring in the home. • Ideal for Triple Play applications such as IPTV, VoIP telephony and high-speed Internet access.
- Page 7 Up to 200 Mbps – ideal for Triple Play applications such as IPTV, VoIP telephony and high-speed Internet access. The BiPAC 2070P links your modem, router, set-top box and PC at speeds of up to 200 Mbps via your household power grid and with QoS prioritization. Features and Specifications Protocols •...
- Page 8 • LED display: - Power - Ethernet (Link/Act) - PLC (Powerline Link/Act) Physical Specification • Dimensions: 75(w) * 114(D) *63 (H) m/m Operation Environment • Operating temperature: 0 ~ 40 ℃ • Storage temperature: -20 ~ 70 ℃ • Humidity: 20 ~ 95% non-condensing Application Diagram:...
-
Page 9: Installation Procedures
Installation Procedures Please extract the HomePlug AV 200 Ethernet Bridge.zip file. Once the zip file is extracted, double click on the Setup.Exe file. You must have Microsoft .NET Framework 1.1 installed before installing Billion BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility. A window will pop-up if you do not have Microsoft .Net framework 1.1 installed. - Page 10 The Billion BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard will appear, click on the button to begin the setup process.
- Page 11 Select the installation destination and select if you will like to install Billion BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard just for yourself or for everyone using this computer and click the button.
- Page 12 Please confirm the installation setup and click on the button to start the installation process.
- Page 13 After the installation process, click the button to exit the Billion BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard Setup Wizard.
- Page 14 Starting the 2070P Device Manager Once the BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard is installed a shortcut will appear on the desktop. You can start the BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard by double clicking on the shortcut, or go through “start”→...
- Page 15 Uninstalling the 2070P Device Manager You can uninstall the BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard going through “start”→“Program”→“ BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility Setup Wizard” and click on UnInstall. Note: You must have Windows Installer installed to perform uninstall.
-
Page 16: Network Information Screen
Understanding BiPAC 2070(P) HomePlug AV 200 Ethernet Bridge Utility 2070P Ethernet Bridge Utility consists of 3 screens accessed through 3 panel tabs. The 3 panels are Network Information, Configuration and Firmware Upgrade located on the top left corner of the program for configuration convenience. - Page 17 and TEI for the station upon which the DM is running. Topology The Topology contains information about the TEI, MAC Address, Bridged MAC Address and the transmit (Tx) and receive (Rx) Coded and Raw PHY rates for all nodes on the network (other than the local STA). The ‘Coded’ rates exclude FEC bits.
-
Page 18: Configuration Screen
Configuration screen This Configuration screen is used to set or change the network password on a remote device identified by its DAK password. Clicking the ‘Set’ button sets the entered passwords. If the DAK password field is left blank, then clicking the ‘Set’... - Page 19 Advanced Setting: QoS Screen BiPAC 2070/2070P provides QoS (Quality of Service) which contains 4 different levels of CAP (Channel Access Priority) to control the speed and priorities of various transmission methods. The 4 different levels of CAP are presented as CAP0, CAP1, CAP2, and CAP3.
- Page 20 IP Port example: In this example one of the destination computers regularly uses the web cam for conference meeting with overseas customers. To ensure that the web cam maintain a high quality voice and video stream, we can set the UDP 5100 (used for web cam protocol) in to the Dest IP Port table by clicking on the Dest IP Port word and entering the port number and selecting the CAP to CAP2.
- Page 21 VLAN ID: IEEE 802.1q contains 12 bits within the data packet to record the VLAN ID. BiPAC 2070/2070P is able to read the VLAN ID to allow the gateway connected behind the BiPAC 2070/2070P to determine what packet is from which LAN.
- Page 22 Priority TTL The Priority TTL contains the option to set the TTL (Time To Live) values for CAP0 to CAP3. The values are set milliseconds ranging between 10 and 65000 msec and it defines the length of time that a data packet should be valid for within the network.
- Page 23 Default CAP The Default CAP contains the option to set the CAP for IGMP, Unicast, IGMP managed Multicast Stream and Multicast/Broadcast. For novice users, we strongly advise not to change the default settings of Priority TTL. IGMP: IGMP’s default CAP is set as CAP3. It is a communication protocol used to manage the membership of Internet Protocol Multicast groups.
- Page 24 Both Multicast and Broadcast are one to many transmissions. The difference between the two is that Multicast requires Multicast Group to be in the same subnet for them to receive the data packets. IGMP The IGMP (Internet Group Management Protocol) contains the option to override defaults to disable Query Timeout within the Group Specific and the All Groups options.
-
Page 25: Firmware Upgrade Screen
Firmware Upgrade screen Firmware Upgrade: This button provides the user with an option to download firmware to upgrade or downgrade across PIB and FW versions. See following description of the Upgrade behavior. The upgrade functionality provides the user with a simple means to migrate back and forth between firmware versions. Clicking on the Firmware Upgrade button will first read the PIB running on the device.
Need help?
Do you have a question about the BiPAC 2070 (P) and is the answer not in the manual?
Questions and answers