Page 2
Hand Held Products. Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
Page 3
This verification system implements an integrated approach that consists of the Quick Check 890 Verifier unit and the Quick Check® ImageData (QCID) software. Quick Check ImageData The Quick Check ImageData (QCID) program was designed for use in conjunction with the QC890 Verifier.
The QC890 Verifier system supports the following interfaces: USB, RS-232, and ® Bluetooth USB Communication Interface For the USB interface, the Hand Held Products CDC-ACM driver must be installed prior to using the QC890 Verifier. This driver is copied to the following directory during install: <install location>/Drivers/USBCOMPortEmulation/hhpcdc.inf The default <install location>...
RS-232 Serial Communication Interface An RS-232 interface requires no additional drivers. Connect the QC890 Verifier to the host as shown in the illustration below. RS-232 Selections Scan the following bar code to select RS-232 communications. RS-232 Communication The RS-232 settings supported are: Baud Rate: 115,200 Parity:...
Laptop. * Bluetooth Connection - PC/Laptop To establish a Bluetooth connection to a PDA or Hand Held Products Mobility Systems device, scan the bar code below, follow the instructions supplied with your Bluetooth device to locate the QC890 Verifier, and connect to it. If you go out of range with your QC890 Verifier, the QC890 Verifier will not re-connect.
Once you initiate a search for devices, a display similar to the one below appears on the host device. The serial number display allows you to confirm that the correct QC890 Verifier has been found. Refer to the Quick Check 890 Verifier User’s Guide for details on the making the Bluetooth connection.
Page 8
The first time you use QCID, the application asks you to select the COM Port to which the QCID is attached. You may select the port by clicking on File-> Preferences. After you make the selection, QCID attempts to connect to the attached QC890 Verifier.
Scanning a Bar Code Symbol Using the QC890 Verifier Note: Calibration is a requirement of the ISO/IEC standards. Refer to the QC890 Verifier User’s Guide or help files for additional calibration information. 1. Place the QC890 Verifier on top of the symbol. 2.
The QC890 Verifier automatically reads the symbol and performs calibration. If the calibration process is successful, the following screen displays. 4. Enter the prompted data (Name and Location) and press OK. The following screen displays. 5. If the unit does not calibrate, contact Hand Held Products Technical Support.
Note: For calibration of external devices, refer to the QC890 Verifier User’s Guide. Technical Assistance If you need assistance installing or troubleshooting, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada: Telephone: (800) 782-4263, option 4 (8 a.m. to 6 p.m. EST)
USB COM ポート エミュレーション QC890 Verifier RS-232 QC890 Verifier USB COM QC890 Verifier USB COM QC890 Verifier * USB COM ポート エミュレーション RS-232 シリアル通信インターフェイス RS-232 QC890 Verifier RS-232 の選択 RS-232 RS-232 通信...
RS-232 ボーレート : 115,200 パリティ : なし データ ビット : ストップ ビット : フロー制御 : なし Bluetooth Bluetooth SPP (Serial Port Profile) QC890 Verifier QC890 SPP Bluetooth QC890 Bluetooth QC890 Bluetooth Bluetooth デバイスと QC890 Verifier の併用 RS-232 Bluetooth QC890 Verifier Bluetooth PC PDA Bluetooth...
Page 27
Bluetooth PDA/M&W Bluetooth Bluetooth QC890 Verifier QC890 Verifier QC890 Verifier Bluetooth Bluetooth 。 * Bluetooth 接続 - PC/ ラップトップ Hand Held Products Mobility Systems Bluetooth Bluetooth QC890 Verifier QC890 Verifier QC890 Verifier QC890 異 Verifier Bluetooth 接続 - PDA/M&W デバイス...