System Menu - Sony HD 3CCD Operating Instructions Manual

SYSTEM Menu

< S Y S T E M >
> I R - R E C E I V E
I M G - F L I P
P A N R E V E R S E
T I L T R E V E R S E
D I S P L A Y I N F O
A N A L O G O U T
S Y N C T Y P E
S Y N C M A S T E R
IR-RECEIVE (infrared signal reception)
When it is set to OFF, the camera does not receive the
signal from the supplied Remote Commander.
Be sure to keep it ON when you use the supplied Remote
Commander.
Note
You cannot set IR-RECEIVE to OFF when you operate
the menu using the supplied Remote Commander. To
set it to OFF, use the RM-BR300 Remote Control Unit
(not supplied) or the VISCA command.
IMG-FLIP (image flip)
Set IMG-FLIP to ON to rotate the camera image
supplied from the RGB/COMPONENT connector
upside down and to reverse the direction of the camera
movement by pan/tilt operation.
Set PAN REVERSE to ON to reverse the horizontal
movement of the camera image.
Set TILT REVERSE to ON to reverse the vertical
movement of the camera image.
When you set IMG-FLIP to ON, "Please restart
system!" appears. Turn off the power of the camera and
turn it on again.
Note
• Regardless of the IMG-FLIP ON/OFF setting, images
shot by the camera are accumulated for the vertical
synchronization period and output from the RGB/
COMPONENT connector of the camera and the
connector on the optional interface board inserted into
the card slot.
• When you set IMG-FLIP to ON, then turn off the
camera and turn it on again, PAN REVERSE and
TILT REVERSE will be set to ON. When you set
IMG-FLIP to OFF, then turn the power off and on
again, PAN REVERSE and TILT REVERSE will be
set to OFF.
DISPLAY INFO (information display)
When the camera settings are stored in POSITION 1 to
16 using the supplied Remote Commander or the RM-
BR300 Remote Control Unit, the message "PRESET
No. xx" automatically appears for 2 seconds on the
O N
monitor screen. If you want to display the message each
O F F
time the camera is operated, set DISPLAY INFO to ON.
O F F
Set it to OFF to cancel the display.
O F F
O F F
Y P P
B R
S Y N C
S T D
The message will appear if the built-in cooling fan of the
camera has accidentally stopped. When DISPLAY
INFO is set to OFF, the display of this message is also
canceled.
ANALOG OUT
Select the signal output from the RGB/COMPONENT
connector on the camera. Select YPbPr for component
signal output, or RGB for RGB signal output.
When RGB is selected with ANALOG OUT, ADD
SYNC appears. If you set ADD SYNC to RGB, a sync
signal is added to each R, G and B signal. If you set it to
OFF, no sync signal is added.
SYNC TYPE appears when either YPbPr or RGB is
selected with ANALOG OUT, and you can select the
type of sync signal,
bi-level sync.
SYNC MASTER
When you connect a sync signal generator, you can
select an output video signal that is synchronized with
the external video sync signal input to the EXT SYNC
IN connector on the camera from the generator.
STD: The output video signal from the RGB/
HD1: The output signal from the HFBK-HD1 HD
SD1: The output signal from the HFBK-SD1 SD
This menu item is available when the HFBK-HD1 or
HFBK-SD1 Interface Board is inserted into the BRU-
H700 HD Optical Multiplex Unit.
Note
SYNC for tri-level sync or VD for
COMPONENT connector on the camera is
synchronized with the external video sync signal.
Interface Board inserted into the camera is
synchronized with the external sync signal.
Interface Board inserted into the camera is
synchronized with the external sync signal.
Note
35
SYSTEM Menu