Test Program For Wm With Timer Pg3 - Gorenje WA63080 Servicing Instructions

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES

Test program for WM with timer PG3

MANUEL ACTION
Press and hold buttons
START/PAUSE and
EASY IRONING and
turn round the program
knob for 1 step in left
(anti-clock side)
~10"
~12"
~4"
~62"+20"
~12"
~77"
~40"
~42"
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV
ACTIVITY
Self test of micro is executed and test program begins:
- all segments on LCD goes ON for 2 sec.
- after 2'' on top line write SELF TEST , on bottom line
write max. spin speed for cotton and 99L and all symbols
are ON
- check if is Water clean sensor connect
(read voltage at empty drum)
All step can be 10".
Door lock control (text on top line DOOR)
- PG3 activated door lock and wait, that contact is close
- max.10 sec)
NTC control (text on top line NTC))
-
check resistance of NTC (can be between 10 to 40°C)
Min. 2 sec
.
Water filling (text on top line WATER)
Open the valves Hot Water, Main Wash and Pre Wash.
Water goes in 3 different space in dispenser.
- HW : 5 '' (space 2), if it is connected to hot/cold water
- PW : 10'' (space 1)
- MW : 10'' (space 2)
- PW + MW : to reach level 1 (space 1,2 and 3)
- when reached level 1 than it is O.K.
- max. time for all is 60"
Water clean sensor (text on top line WATER SENSOR)
Only check if it is connected (check voltage at water in
drum together 10")
Washing and heating (text on top line WASHING)
- Washing: 15''ON / 5''OFF / 15''ON/5''OFF
- 3 times repeats washing
- last wash is in spin direction and without pause
- Heater ON all time of washing
All together is 75''. After this time switch OFF heater,
washing goes to spinning.
Spinning with water (text on top line SPIN)
- 40'' spin from 50rpm to max.50 rpm
(or speed define with Pad's, if is lower that 500 rpm)
- wait to drum stop
Draining (text on top line DRAIN)
- switch pump ON for 40 "
Check if water level fall under level 1
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: +386 63 8990 / 8992 432
Telefax : +386 63 8992 794
4-027-0706
INDICATION
•
If self test O.K, than on top line
write OK (for 2'') and all other
segments and symbols switch OFF
•
If self test is not O.K., than on top
line write ERROR all other
segments and symbols switch OFF,
WM stop
•
If it is O.K. than on top line write
DOOR OK (for 2'')
•
If it is not O.K. than on top line
write DOOR ERROR, WM stop
•
If it is O.K. than on top line write
NTC OK (for 2'')
•
If it is not O.K. than on top line
write NTC ERROR, WM stop
•
If it is O.K. (before 60" reach level
1) than on top line write WATER
OK (for 2'')
•
If it is not O.K. than on top line
write WATER ERROR, WM stop
•
If it is connected than on top line
write WATER SENSOR YES (for
2'')
•
If it is not connected than on top
line write WATER SENSOR NO
•
If it is O.K. (after finish wash) –
washing in both direction, than on
top line write WASHING OK (for
2'' – can be 2" in spinning)
•
If it is not O.K. than on top line
write WASHING ERROR (for 2''),
WM stop
•
If it is O.K. than on top line write
DRAIN OK (for 2'')
•
If it is not O.K. than on top line